Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Any codes issue here?

User: anbm, Location: TX

Asked on: Friday, August 22, 2025 at 11:19 am EDT
Answered on: Friday, August 22, 2025 at 11:19 am EDT

Question: See attached image for sketch of elec. one line diagram, does anyone see any code issue?I.e. using new 400A services (both normal and generator power) to power an existing 1,000A panel with 1,000A main breaker becausemax. demand load of the panel is only 210A. No need to comply with coordination study in this case? Thank you.

Okay, I've reviewed the one-line diagram you've provided. Here's my assessment of potential code issues and considerations, keeping in mind I'm providing advice based on the information available and you should always consult a qualified electrical engineer for a definitive and code-compliant design

Potential Code Issues and Considerations:

1. Parallel Operation and 705.40

This is the most prominent issue. You are effectively operating the normal service and the generator in parallel, even though they are connected through the 1000A Main Breaker. NEC 705.40 is very relevant and likely applies. This section addresses interconnected power sources.

705.40 requires the sum of the power source OCPD's (400A and 400A) to not exceed the ampacity of the busbars or conductors.
In your case, the 400A + 400A = 800A, which is less than the 1000A busbar rating of the existing panel. On the surface, this seems to be compliant. However, the way you've implemented this might create a violation, depending on interpretation by the AHJ. I would be very cautious and prepared to justify it. Rationale for Concern

While the total OCPD rating is less than the busbar rating, the intent of 705.40 is to prevent the busbar from being overloaded by simultaneous contributions from multiple sources. Even though the load is only 210A, in a fault condition, both the normal and generator sources could contribute fault current to the 1000A panel busbar, potentially exceeding its interrupting rating or causing damage.

Mitigation/Clarification Strategies



Verify Fault Current Calculations

Perform a fault current study to confirm that the maximum available fault current from both sources combined does not exceed the 1000A panel's short-circuit current rating. This is critical and could be the deciding factor.

Transfer Switch Interlock

A
break-before-make transfer switch is crucial to prevent paralleling during switching. Your one-line doesn't explicitly show the type of transfer switch. If you're relying on the main breaker to prevent paralleling, you need to demonstrate to the AHJ that it's physically impossible to have both sources feeding the panel simultaneously (e.g., a robust mechanical interlock).

AHJ Interpretation

Discuss your design with the Authority Having Jurisdiction (AHJ) before installation. They may have specific interpretations or requirements regarding parallel operation, even in this configuration. Getting their buy-in early is essential.2.

Overcurrent Protection (OCPD) and Selective Coordination (especially if required)



Existing 1000A Main Breaker

The 1000A breaker protects the panel's busbars (which are rated 1000A). That part is compliant. However, the fact that your actual load is only 210A raises a point.


Feeder Protection

The 400A breakers are protecting the feeder conductors from the normal service and the generator. This is compliant.

Selective Coordination

IF selective coordination is required by code (e.g., essential systems in healthcare facilities, emergency systems), you need to demonstrate that the 400A breakers will trip before the 1000A breaker in an overcurrent or fault condition. Given the large difference in size, this is unlikely to be a problem, but it needs to be verified with a coordination study if selective coordination is required.3.

Service Disconnects



Adequacy

The 400A breakers serve as the service disconnects for the normal and generator services. This is acceptable.

Accessibility

Ensure the disconnects are readily accessible (NEC 230.70).
4.


Generator Sizing and Load Calculations



Generator Capacity

Verify the generator is adequately sized to handle the 210A load, with sufficient margin for future expansion (if planned).

Load Calculation

Ensure the 210A demand load is a well-documented and accurate calculation per NEC Article 220.5.

Grounding and Bonding



Proper Grounding

Verify that the grounding and bonding are properly implemented according to NEC Article 250 for both the normal and generator services. This includes grounding electrode conductors, bonding jumpers, and equipment grounding conductors.6.

Short-Circuit Current Rating (SCCR) of Equipment



Adequacy

Confirm that all equipment in the system (panels, breakers, etc.) has a short-circuit current rating (SCCR) sufficient to withstand the available fault current at their location. The available fault current from the utility and the generator needs to be calculated at each point.

Why a Coordination Study Might Be Needed (Even with a Small Load)

Even though your load is significantly smaller than the panel's capacity, a coordination study might still be necessary if:


Code requires selective coordination
(as mentioned above). The AHJ requests it. There are critical loads that require minimal downtime. A coordination study helps minimize the extent of outages during faults.

In summary, the biggest potential issue is 705.40. A fault current study is highly recommended to prove your design meets the requirements and to avoid any confusion, seek input from AHJ before installation. Also consider if you need to comply with selective coordination. Make sure your design is in compliance with all applicable codes.Disclaimer: This analysis is based solely on the provided one-line diagram. A comprehensive electrical design requires detailed load calculations, fault current analysis, coordination studies, and a thorough understanding of the applicable codes and standards. Always consult with a qualified electrical engineer. Flag for review

Previous Question Next Question