Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Low hp DC motor starting

User: jminer99er, Location: Sacramento, CA

Asked on: Friday, August 22, 2025 at 12:24 pm EDT
Answered on: Friday, August 22, 2025 at 12:35 pm EDT

Question: Im adding a new ¾ hp DC motor at 24Vdc to a hydraulic unit. This will be remote operated via mometary push buttons.My questions is DC rated contactor/motor starter options. The motor is 3/4hp 1800rpm, 4pole, 24Vdc. The nameplate says A.ARM 31.8. I was thinking like nema 2 contactor, but I'm not sure if it's DC rated and have options for 24Vdc coils. Im not fimilar with dc motor starting. What would be some starting installation options?

You're on the right track thinking about a contactor. Here's a breakdown of your options and considerations for DC motor starting

Understanding the Challenges with DC Motors
Inrush Current

DC motors, especially at startup, draw significantly higher current than their running current. This inrush current can be 5-10 times the full load amps (FLA), potentially damaging the motor or stressing the power supply.


Arcing

DC circuits are prone to more severe arcing than AC circuits when contacts open and close. This is due to the continuous current flow and the absence of natural current zero crossings like in AC. This makes proper DC-rated contactors essential.

Voltage Drop

High inrush currents can cause significant voltage drops, especially in long wire runs or with undersized power supplies.

Sizing the Contactor
1. Calculate Full Load Amps (FLA)

You have the A.ARM (Armature Amps) of 31.8A. This is the key number for your contactor selection.
2.


Contactor Rating

You need a
DC-rated contactor that can handle at least 31.8A continuously. However, you should oversize the contactor to account for:

Inrush Current

A safety factor of 1.5 to 2x the FLA is recommended. So, you should look for a contactor rated for around 48A - 64A DC.

Duty Cycle

If the motor starts and stops frequently, the contactor will experience more wear and tear. Oversizing helps with this.


Future-Proofing

It's often better to select a slightly larger contactor than immediately needed for future flexibility if you upgrade the motor.3.

Coil Voltage

Make sure the contactor coil is rated for 24V DC. This is critical.

Contactor Options
Definitely use a DC-Rated Contactor

This is
essential. Don't try to use an AC contactor on a DC circuit. AC contactors are not designed to extinguish DC arcs and will fail quickly.

Consider Industrial Control Suppliers

Look to reputable suppliers like:

Eaton

They have a wide range of DC-rated contactors.


Allen-Bradley (Rockwell Automation)

Another reliable source for industrial control components.

Schneider Electric

Offers various motor control solutions.


Siemens

A global leader in automation and electrical components.

Key Features to Look For



DC Rating (Amps and Voltage)

Verify the contactor is rated for the voltage and current you need.

Coil Voltage

Ensure the coil is 24V DC.


Auxiliary Contacts (Optional but Recommended)

Auxiliary contacts can be used for interlocking, status indication (e.g., "motor running" light), or connection to a PLC or other control system.

Arc Suppression

Many DC contactors incorporate arc suppression features (e.g., blow-out magnets, special contact materials) to improve contact life.


NEMA Size

NEMA sizes are a guideline for physical size and contact capacity. A NEMA Size 1 or Size 2 might work, but the DC amperage rating is the critical factor. Don't rely solely on NEMA size; focus on the current rating. The exact NEMA size that meets your DC amperage requirements will depend on the specific manufacturer and contactor series. A larger NEMA size often implies a higher current rating.

Solid State Relays (SSRs)

These are a good option, but require careful consideration. Ensure the SSR is DC rated for the current and voltage. They also need heat sinking.

Starting Methods (and Why You Probably
Don't Need Anything Fancy)


For a relatively small 3/4 HP motor, you probably
don't need a complex starting method. Simple direct-on-line (DOL) starting with the contactor is likely sufficient. More complex methods are typically used for larger DC motors to limit inrush current and reduce stress on the power supply. Direct-On-Line (DOL) Starting



Simplest

The contactor directly connects the motor to the power supply.


High Inrush Current

This is the biggest drawback.

Suitable for Smaller Motors

Generally fine for motors up to a few horsepower.


Other Starting Methods (Less Likely Needed)



Series Resistance Starting

A resistor is placed in series with the armature during startup to limit current. The resistor is gradually shorted out as the motor speeds up. This requires multiple contactors and a timing circuit.


Solid-State Soft Starters

These use solid-state devices (SCRs or transistors) to gradually increase the voltage applied to the motor, reducing inrush current. They offer more control than resistance starting but are more complex and expensive. This may be an option depending on how sensative your application is, or if the power supply is small.

Installation Considerations
Wiring

Use appropriately sized wire for the current. Consult a wiring chart based on the amperage and length of the run.


Overcurrent Protection

A circuit breaker or fuses are essential to protect the motor and wiring from overloads and short circuits. Size the overcurrent protection according to the motor's FLA and the relevant electrical codes. Consider using a slow-blow fuse or a circuit breaker with a C or D curve (designed to handle inrush currents).

Control Circuit

The momentary push buttons will control the contactor coil. A simple latching circuit using a relay is often used:


Start Button

Momentarily energizes a relay (or uses the contactor's auxiliary contact to latch itself on).

Stop Button

Breaks the relay (or contactor) coil circuit.


Arc Suppression (Across Contactor Coil)

Even if the contactor has built-in arc suppression, it's good practice to add a diode (for DC circuits) across the contactor coil to suppress voltage spikes when the coil is de-energized. A flyback diode will protect the rest of the control circuitry.

Enclosure

Mount the contactor and other components in a suitable enclosure to protect them from the environment.

Example Installation


Here's a simplified schematic (you'll need to adapt it to your specific needs):

+24V DC -----------------------
--- Start Button (Momentary N.O.) ---
--- Stop Button (Momentary N.C.) ----|--- Relay Coil (24V DC) --- Diode (Across Relay Coil) ---
|GND ------------------------------------------------------------------------------------------Relay Contacts (N.O.) --- Contactor Coil (24V DC) --- Diode (Across Contactor Coil) --- GNDContactor Main Contacts --- Motor Armature --- GND
Steps to Choose the Right Contactor and Install1. Determine FLA

You already have this (31.8A).
2.


Calculate Inrush Current (Estimate)

Assume 5-7x FLA for initial estimate.3.

Select Contactor

Choose a
DC-rated contactor with a continuous current rating significantly higher than the FLA (e.g., 50-60A or more) and a 24V DC coil. Prioritize the DC amperage rating over NEMA size.4.

Choose Overcurrent Protection

Size the fuse or circuit breaker appropriately.5.

Wire Everything Correctly

Use the correct wire gauge and follow best practices for electrical wiring.6.

Test

Thoroughly test the circuit before putting it into service.

Important Safety Notes:
Always disconnect power before working on any electrical equipment. Work in accordance with all applicable electrical codes and regulations. If you're not comfortable working with electrical systems, consult a qualified electrician.By carefully considering these factors, you can select the right DC contactor and ensure a reliable and safe motor starting system for your hydraulic unit. Remember to over-engineer the contactor selection for DC motors. Flag for review

Previous Question Next Question