Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Rewing Hunter fan pull chain

User: Greg1707, Location: Alexandria, VA

Asked on: Friday, August 22, 2025 at 4:51 pm EDT
Answered on: Friday, August 22, 2025 at 4:51 pm EDT

Question: I have a Hunter original fan. It must be 30 year old. The fan is controlled by a wall switch/speed control. I will spare you the details but I would like to disconnect/disable the pull chain switch. The fan would be permanently wired for high speed and the wall control will do the rest.The pull chain switch has several wires. Any ideas how to do this?

Okay, I understand. Disabling the pull chain switch and wiring the fan for permanent high speed controlled only by the wall switch is a doable project. However, safety first! Before you start, make sure to:1. Turn off the power

Locate the circuit breaker that controls the fan and switch it off. Double-check with a non-contact voltage tester to ensure the wires you'll be working with are dead.2.

Wear appropriate safety glasses.


Here's a general approach to this project. Note: The exact wire colors may vary based on the age of your fan. I am working on the assumption you have a 3-speed fan with a capacitor.

Understanding the Basics



Line Voltage

This is the power coming from your circuit breaker (typically black wire in North America).


Neutral

The return path for the electricity (typically white wire).

Fan Motor

Has several windings (coils of wire) that create different speeds. The pull chain switch selects which winding is energized, and the capacitor assists in making the fan motor work properly.


Capacitor

Often a small, rectangular component with multiple wires. It's essential for starting and running the motor smoothly at different speeds. It should remain connected.

General Instructions (Disclaimer at the end)


Access the Wiring

Carefully remove the fan's lower canopy or housing to expose the wiring. Take pictures before you start disconnecting anything! This is a lifesaver if you get confused.2.

Identify the Wires

You will likely have the following wires coming from the fan motor and going to the pull chain switch:

Black (or Blue)

This is probably the "high-speed" wire.


Other Colors

These are likely for medium and low speeds. These colors can include blue, yellow, or other colors.

Neutral (White)

This usually bypasses the pull chain switch and connects directly to the incoming neutral wire.
You'll also have:

Line Voltage In

Usually black, coming from the wall switch.


Neutral In

Usually white, coming from the electrical panel.

Important

Confirm these assumptions with your multi-meter.3.

Disconnect the Pull Chain Switch

Carefully disconnect all the wires from the pull chain switch. Cap off the unused speed wires with wire nuts.4.

Connect for High Speed

Connect the Line Voltage In (from the wall switch) directly to the Black (or Blue) wire that goes to the fan motor. This is the high-speed wire. Double-check that the Neutral In wire is still connected directly to the fan motor's Neutral wire (usually white). Make sure all connections are secure with wire nuts.5.

Cap Off Unused Speed Wires

Using wire nuts, individually cap off all the other speed wires that used to go to the pull chain switch (the ones for medium and low speed). These are now unused.6.

Reassemble and Test

Carefully tuck all the wires back into the housing, making sure nothing is pinched or touching the moving parts of the fan. Reassemble the fan's canopy or housing. Turn the circuit breaker back on. Test the fan using the wall switch. It should run only on high speed.

Important Considerations



Capacitor

The capacitor is crucial for proper fan operation. Do not disconnect it. It should already be wired into the circuit, likely between the motor windings and the neutral wire. It typically stays connected regardless of what you're doing with the pull chain switch. If you're unsure about the capacitor wiring, take clear pictures before you start disconnecting anything.

Wall Switch/Speed Control

Make sure your wall switch is rated for the fan's motor load. Some dimmer-type switches are not suitable for fan motors and can damage them.


Older Wiring

Be extremely careful with older wiring. The insulation can be brittle and crack easily. If you see damaged wiring, consider replacing it.

Specific Steps and Troubleshooting


If the fan doesn't run

Double-check all your connections. Make sure the line voltage is connected to the high-speed wire, the neutral is connected, and the capacitor is correctly wired (if applicable).2.

If the fan hums but doesn't spin

This could be a problem with the capacitor. It might be failing and need replacement. This may also be an issue with the motor, or something is impeding the motor from spinning freely.3.

If the fan runs backward

Some fans have a reversing switch. Make sure it's in the correct position.4.

Consult an Electrician

If you're uncomfortable with any of these steps, or if you encounter problems you can't resolve, please consult a qualified electrician. It's better to be safe than sorry, especially when dealing with electricity.

Disclaimer



I am an AI Chatbot and cannot provide electrical advice. Working with electricity can be dangerous and potentially lethal. The instructions above are general guidelines based on common practices, but your specific fan wiring may be different. I strongly recommend consulting a qualified electrician for this type of project. You are responsible for your own safety and any damage that may occur as a result of following these instructions.


Good luck with your project, and please be careful! Flag for review

Previous Question Next Question