Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 240 volt Dryer controls 120v booster fan?

User: sw_ross, Location: NoDak

Asked on: Monday, August 25, 2025 at 7:17 pm EDT
Answered on: Monday, August 25, 2025 at 7:21 pm EDT

Question: If a booster fan was needed due to a long run of venting how would you control the booster fan by automatic method so when the dryer turns on the 120v booster fan kicks on?Thanks!

Okay, here's a breakdown of how to automatically control a 120V booster fan for a dryer, so it activates when the dryer is running

Core Concept:

You need a way to sense when the dryer is operating and use that signal to switch the booster fan. The most common and safest approaches involve non-invasive current sensing.

Methods1. Current Sensing Switch/Relay



How it Works

This is the most common and recommended method. A current sensing switch (also called a current operated switch or current transformer relay) clamps around one of the dryer's power cords (typically the "hot" wire). When the dryer draws current, the sensor detects the magnetic field created by the current flow and closes a switch (or energizes a relay). This switch then completes the circuit to power on your booster fan.


Pros

Non-invasive (no wire cutting needed). Safe (low voltage control circuit). Reliable. Adjustable (many have sensitivity adjustments). Relatively easy to install.

Cons

Requires purchasing a current sensing switch (cost varies). Needs to be properly sized for the dryer's amperage.

Wiring

1. Clamp the current sensor around one of the dryer's power cord wires (while unplugged, obviously!).
2. Connect the sensor's output wires to the coil of a 120V relay (if the sensor output is low voltage - typically it will be if it's solid state). If the sensor has a 120v output, you can skip the relay and go directly to the fan.3. Wire the 120V relay's normally open (NO) contacts in series with the 120V power supply and the booster fan. When the relay is energized (dryer running), the contacts close, powering the fan.


Parts

Current Sensing Switch (e.g., Functional Devices RIBCL20 or similar) - Make sure it can handle the dryer's amperage range. A range of 0-10 amps is usually sufficient, but check your dryer's specs. Optional: 120V Relay (if needed). Electrical enclosure to house the relay (for safety). Wiring and connectors.2.

Vibration Sensor



How it Works

A vibration sensor detects the vibrations of the dryer when it's running. This sensor sends a signal to a control circuit (typically a microcontroller or a specialized vibration switch) that then activates a relay to power the booster fan.


Pros

Non-invasive (no wire cutting needed). Can be used even if you can't easily access the dryer's power cord.

Cons

Can be less reliable if the dryer's vibrations are inconsistent. May be more complex to set up, depending on the sensor and control circuit. May be triggered by other nearby vibrations.

Wiring

1. Mount the vibration sensor on the dryer (use adhesive or a clamp).
2. Connect the sensor's output to a vibration switch or a microcontroller (like an Arduino) programmed to trigger a relay.3. Wire the relay's normally open (NO) contacts in series with the 120V power supply and the booster fan.


Parts

Vibration Sensor (e.g., a piezo vibration sensor). Vibration Switch or Microcontroller (Arduino is common). 120V Relay. Electrical enclosure. Wiring and connectors.

Important Considerations and Safety



Electrical Safety



Always disconnect the power to the dryer before working on any wiring.
If you are not comfortable working with electrical wiring, hire a qualified electrician. Improper wiring can be dangerous and create a fire hazard. Local Codes

Check your local building codes and electrical codes to ensure your installation is compliant. Some jurisdictions may require a permit for this type of work.


Enclosure

Mount the relay and any other control circuitry in an approved electrical enclosure to protect it from dust, moisture, and accidental contact.

Amperage Rating

Ensure all components (current sensor, relay, wiring) are rated for the amperage of the booster fan and the dryer circuit.


Dryer Overload Protection

Do not interfere with the dryer's existing overload protection. Make sure your booster fan and its control circuit do not add an excessive load to the dryer's circuit.

Fan Placement

Ensure the booster fan is installed in a location that complies with the fan manufacturer's instructions and building codes. Consider noise levels.


Current Sensor Sensitivity

Adjust the sensitivity of the current sensor (if adjustable) to prevent false triggers (e.g., from the dryer's standby power consumption).

Grounding

Make sure the booster fan and any metal enclosures are properly grounded.

Example Implementation (Current Sensing Switch)


Purchase

A current sensing switch (rated for the dryer's amperage) and a suitable 120V relay. Also get an electrical junction box.2.

Safety First

Unplug the dryer from the wall.3.

Mount

Install the current sensing switch around one of the dryer's power cord wires (inside the dryer's access panel if possible, or in a separate junction box).4.

Wiring

Connect the current sensor's output wires to the coil of the 120V relay (inside the junction box).* Wire the relay's normally open (NO) contacts in series with the 120V power supply and the booster fan. This means you'll cut one of the 120V wires that would normally go directly to the fan and connect the two ends to the relay's NO contacts.5.

Enclose

Place the relay and any wiring connections inside the electrical junction box.6.

Test:
Plug the dryer back in and run a test cycle. The booster fan should turn on when the dryer starts.By using a current sensing switch, you create a safe and reliable system that automatically activates the booster fan only when the dryer is actually running. Remember to always prioritize safety and consult with a qualified electrician if you have any doubts. Flag for review

Previous Question Next Question