Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Transformer grounding

User: Roscoe, Location: Oh

Asked on: Monday, August 25, 2025 at 10:00 pm EDT
Answered on: Monday, August 25, 2025 at 10:00 pm EDT

Question: So my question, for everyone is about my ground rod, either being on the service disconnect before the transformer as my local authority recommends, or should I drive my ground rod run my number six to the transformer, ground lugs, and then back to the disconnect that is feeding the step down transformer. Step down transformer is a 45KV480 V Y down to 2083 phase, my feeders are coming from the building on the other side of the property underground to a 480 V service disconnect with just the AB and C phase conductors as well as my ground. So is it recommended that I drive a ground rod near my disconnect and run an additional number six from the ground rod to the service disconnect, which would be on the primary side before the transformer, and then out of the disconnect to the transformer and continue it all the way through to the new load center?

Okay, this is a crucial question regarding grounding and bonding of a step-down transformer. Let's break down the situation and the code requirements to determine the best approach. Given your description, it sounds like you're dealing with a separately derived system.

Understanding Separately Derived Systems (SDS)

A step-down transformer that derives a new voltage (in your case, 208Y/120V from 480V) is typically considered a Separately Derived System (SDS) according to the NEC. This means the 208Y/120V side is treated as if it's coming from a completely new power source, independent of the 480V source. This has significant implications for grounding.

Key NEC Requirements (Refer to NEC Article 250, especially Part IV - Grounding and Bonding of Separately Derived Systems) Grounding Electrode System (GES) at the SDS

The NEC
requires a grounding electrode system at the separately derived system (the 208Y/120V side of your transformer). This is fundamental to establishing a low-impedance path for fault current back to the source.

Bonding Jumper (System Bonding Jumper)

You must have a bonding jumper (often called a System Bonding Jumper) connecting the transformer's neutral point (the center of the 208Y/120V wye) to the transformer's enclosure and to the grounding electrode conductor. This jumper carries fault current back to the source and is critical for proper overcurrent device operation. The size of this jumper is determined by NEC 250.28(D).

Grounding Electrode Conductor (GEC)

This conductor connects the transformer's neutral point
and the enclosure/frame of the transformer to the grounding electrode system (ground rods, etc.). The size of this conductor is determined by NEC Table 250.66, based on the size of the ungrounded conductors (phase wires) on the secondary (208Y/120V) side of the transformer.

Bonding to Metal Enclosures

All metallic enclosures containing conductors (conduit, junction boxes, panelboards) must be properly bonded together and connected to the grounding system.

No Direct Connection to Primary Side Ground

It is generally
not permitted to run a grounding electrode conductor (GEC) from the primary side (480V) to the ground rods at the transformer. This is because the primary side and secondary side are intended to be grounded separately for safety reasons. A ground fault on the secondary side should clear through the SDS grounding system, not through a path back to the primary side ground.

Analysis of Your Scenarios and Recommendations



Scenario 1: Ground Rod at Primary Disconnect (What your Local Authority Recommends)
This is NOT the correct method based on standard NEC practices for an SDS. While grounding the primary disconnect is important, it doesn't address the critical requirement of establishing a dedicated grounding system at the separately derived system (your transformer). You are already running a ground conductor back to this point, so establishing another ground rod here would not be necessary.

Scenario 2: Ground Rod at Transformer and Back to Primary Disconnect This is closer to the correct method, but still has problems. Driving a ground rod at the transformer is necessary. The code does not require the secondary side ground to run back to the primary side. However, it will need a proper bonding jumper to the transformer's enclosure and a grounding electrode conductor that is grounded to the rod.

Recommended Solution (NEC Compliant)

Here's the step-by-step approach you should take:1.

Drive Ground Rods at the Transformer Location

Drive two (or more if required by local code) ground rods at the location of your transformer. Space them at least 6 feet apart. Use appropriate sized ground rods, usually 8' length minimum.2.

Size the Grounding Electrode Conductor (GEC)

Determine the size of the ungrounded (phase) conductors on the
secondary (208Y/120V) side of the transformer. Use NEC Table 250.66 to determine the required size of the Grounding Electrode Conductor (GEC) based on the size of these ungrounded conductors.
3.


Size the System Bonding Jumper

Determine the size of the ungrounded conductors on the secondary side of the transformer. Use NEC Table 250.28(C) to determine the required size of the bonding jumper.
4.


Connect the System Bonding Jumper

Connect the system bonding jumper from the transformer's neutral point (X0) to the transformer's enclosure.5.

Connect the Grounding Electrode Conductor (GEC)

Connect the GEC from the transformer's neutral point (X0) (and the enclosure) to the ground rod(s) you installed. You can use a split-bolt connector or other listed grounding connector to connect the GEC to the ground rods. Ensure the connection is properly made and protected from corrosion.6.

Run a Ground Conductor from the Primary Disconnect to the Transformer

You already have a ground conductor running with your 480V feeders from the primary disconnect to the transformer. Ensure this conductor is sized according to NEC 250.122 based on the size of the overcurrent protective device protecting the 480V feeders. This conductor serves as the
equipment grounding conductor (EGC) for the transformer enclosure and the 480V primary disconnect switch. It is essential for fault current return on the 480V side.7.

Bonding at the 208Y/120V Panelboard (Load Center)

In the 208Y/120V panelboard that is fed from the transformer, you will also need to ensure proper bonding. The neutral bus must be isolated from the panelboard enclosure (as it is a separately derived system and the neutral is grounded
only at the transformer). Run an appropriately sized equipment grounding conductor (EGC) from the transformer to this panelboard.

Important Considerations



Local Codes and AHJ

Always check with your local Authority Having Jurisdiction (AHJ, i.e., the electrical inspector) for any specific requirements or interpretations of the NEC. They have the final say on what is acceptable in your area.

Qualified Electrician

This work should be performed by a qualified and licensed electrician who is familiar with the NEC and local electrical codes. Improper grounding can be extremely dangerous and can result in electrical shock, fire, and equipment damage.


Overcurrent Protection

Ensure that the overcurrent protective devices (circuit breakers or fuses) on both the primary (480V) and secondary (208Y/120V) sides of the transformer are properly sized to protect the transformer and the connected loads.

Transformer Nameplate

Refer to the transformer's nameplate for specific grounding and bonding recommendations from the manufacturer.


Documentation

Keep thorough records of all grounding and bonding connections, conductor sizes, and grounding electrode system components. This will be helpful for future maintenance and troubleshooting.

In summary, focus on establishing a complete and independent grounding system at the 208Y/120V side of your transformer. Do not rely solely on the grounding from the primary side disconnect. Following these steps and consulting with a qualified electrician will ensure a safe and code-compliant installation.
Flag for review

Previous Question Next Question