User: thepij, Location: South Killingly, CT
Asked on: Tuesday, August 26, 2025 at 8:44 am EDT
Answered on: Tuesday, August 26, 2025 at 8:45 am EDT
Question: We designed a rooftop unit (RTU) and per manufacturer it has a 60 amp MOCP. We derived power from local bus duct and provided 60 amp fuses in the bus disconnect. Feeder to unit was designed per manufacturer's MCA. When RTU arrived on the job it came with a 125 amp circuit breaker installed, even though the nameplate stated 60 amp MOCP. Client is asking if this is ok or not. As designed the 125a c/b would act only as a local disconnect and not provide any overcurrent protection. Is anyone aware of a code issue with leaving the 125 amp c/b installed or should it be replaced with a 60 amp c/b.
You've hit a common, and potentially problematic, situation. Here's a breakdown of the code implications and how to approach this
Understanding the Terms (Key to Everything)
MOCP (Maximum Overcurrent Protection)
This is the maximum size overcurrent protective device (fuse or circuit breaker) the manufacturer allows to protect the unit. Exceeding this voids the warranty and poses a significant safety risk.
MCA (Minimum Circuit Ampacity)
This is the minimum ampacity of the conductors supplying the unit. It accounts for motor starting currents and other factors.
Overcurrent Protection
Primarily serves to protect the equipment (RTU) from damage due to overloads and short circuits.
The Code Issues1. NEC 110.3(B) - Listing and Labeling
This is a cornerstone of the NEC. It states that listed or labeled equipment must be installed and used in accordance with any instructions included in the listing or labeling. The MOCP on the nameplate is part of that listing. Installing a breaker larger than the MOCP violates this section.2.
NEC 440.22(A) - Hermetic Refrigerant Motor-Compressor
This section, specifically addressing HVAC equipment with motor-compressors, dictates how the overcurrent protection is to be sized. The MOCP on the nameplate is a direct result of the calculations required by this section. Exceeding it is a violation.3.
Potential Damage and Safety Hazard
The manufacturer sets the MOCP to protect the components within the RTU. A larger breaker won't trip quickly enough to prevent damage to these components in an overload situation. This can lead to premature failure, fires, or other hazards.
Analysis of the Situation Your Design
You correctly designed the feeder conductors based on the MCA and provided 60A fuses at the bus disconnect, adhering to the manufacturer's MOCP.
The Problem
The RTU arrived with a 125A circuit breaker installed in the unit itself. This contradicts the nameplate and is a violation of the NEC.
The Client's Question
The client is right to be concerned. Leaving the 125A breaker would effectively negate the overcurrent protection for the RTU. The 60A fuses at the bus disconnect would protect the feeder conductors, but not the RTU's internal components.
The Correct Solution1. Contact the Manufacturer IMMEDIATELY
This is the most crucial step. You need to understand why the unit was shipped with a 125A breaker when the nameplate specifies 60A MOCP. It could be:
A Manufacturing Error
This is the most likely scenario. The wrong breaker was installed at the factory.
A Misunderstanding by the Manufacturer
Less likely, but possible, the manufacturer might have thought the 125A breaker was allowed based on some internal testing (highly unlikely, given the nameplate).
A Modification
Extremely unlikely but must be ruled out. Was the unit somehow modified in the field?2.
Follow the Manufacturer's Instructions
The manufacturer will provide the definitive solution. They will likely instruct you to replace the 125A breaker with a 60A breaker that meets their specifications. They might issue a revised nameplate if, and only if, they can justify a higher MOCP through proper engineering calculations and testing.3.
Document Everything
Keep meticulous records of your communication with the manufacturer, their instructions, and any changes made to the unit. This documentation is crucial for warranty claims and liability protection.
Why You Can't Just Use the 125A as a Disconnect It's Misleading and Dangerous
A circuit breaker is designed to provide overcurrent protection. Having a 125A breaker where a 60A breaker is required creates a false sense of security. Anyone working on the unit might assume it's protected at 125A, which is wrong.
Code Violation
As mentioned above, NEC 110.3(B) and 440.22(A) are violated.
Warranty Issues
Using a breaker larger than the MOCP likely voids the manufacturer's warranty.
In Summary
The 125A breaker must be addressed. Do not leave it in place. Contact the manufacturer to understand the discrepancy and follow their instructions to correct the situation. Replacing it with a 60A breaker is the most likely solution, but get that confirmation from the manufacturer first. Prioritize safety and compliance with the NEC. Flag for review