Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 240.21(C)(2) & (3) with PV

User: SteveO NE, Location: Northeast

Asked on: Tuesday, August 26, 2025 at 10:49 am EDT
Answered on: Tuesday, August 26, 2025 at 10:55 am EDT

Question: In light of the other thread that just popped up discussing transformers I thought I'd put this out there for discussion as well because I have seen interpretations both ways.Do you consider PV an industrial installation as it pertains to 240.21(C)? Is there any overarching definition I am missing, not specifically designated to another section of the code (for instance 240.2 specifically states its applicable to Part VII meaning it is not applicable to other parts) that would preclude this? Power generation is considered an industrial application, and (C)(3) does not refer to the facility itself (whereas again 240.2 specifically does), just "the installation", so presuming there are no loads on the transformer other than power generation and station service associated with that power generation, would you, or would you not allow those conductors to be 25' presuming you also meet the 4 conditions outlined. Notwithstanding art 408, and protection of the panelboard itself, this also allows the conductor to be protected by the sum of the breakers in an MLO vs a single OCPD.

This is a great question that dives deep into code interpretation. Here's a breakdown of my thought process and why I lean towards YES, PV installations can qualify as "industrial installations" for the purposes of 240.21(C), under specific conditions, though it's not a slam dunk and AHJ buy-in is crucial.

My Reasoning for YES (with conditions)



"Industrial Installation" is not explicitly defined widely

The NEC uses the term "industrial" a lot, but a universally applicable, overarching definition is lacking. We must rely on context and the ordinary meaning of the word. The ordinary meaning of "industrial" as it applies here would be
pertaining to or characteristic of industry. The key question is what constitutes “industry” when considering solar PV installations.

Power Generation IS Industry

The production of electricity, regardless of source (coal, natural gas, nuclear, solar, wind, etc.) is considered part of the energy industry. Utility-scale power plants are unequivocally industrial installations. Smaller PV installations, especially those designed for grid-tied export, fall under the umbrella of energy production, and thus the installation can be considered “industrial.”

Focus on the Installation, Not the Building

240.21(C)(3) speaks to "the installation," not the type of occupancy of the building. The "installation" refers to the components of the electrical system itself, and is the electrical connection from the PV array to the grid.


Dedicated Power Generation

The key is dedicated. The exception hinges on the transformer only serving power generation equipment. If the transformer also feeds loads unrelated to power generation (e.g., general lighting, HVAC for a non-essential office, etc.), then it's much harder to argue for the industrial exception. However, if it ONLY serves PV inverters, monitoring equipment, and essential station service equipment (e.g., lighting and climate control for the inverter room), then the argument becomes stronger.

Meeting the Conditions of 240.21(C)(3)

You
must meticulously meet all four conditions listed in 240.21(C)(3) for the 25-foot tap rule. This includes:

Conductor ampacity

The conductors must have an ampacity of at least 1/3 of the OCPD protecting the feeder.

Termination

The conductors must terminate in a single OCPD or set of OCPDs that limits the load to the ampacity of the conductors. The sum of OCPD's can be used in an MLO panelboard, but remember this exception does not allow you to circumvent Art. 408's overcurrent protection requirements.


Enclosed in a Raceway or Protected

The conductors must be enclosed in a raceway or otherwise protected from physical damage.

Length Limitation

Obviously, the conductors cannot exceed 25 feet in length.

Arguments Against (Why It's Not Always Clear-Cut)



Residential PV

A small rooftop residential PV system feeding a residential load center would be a very hard sell as an "industrial installation." It's primarily serving the residential load, not generating power for wider distribution.

Commercial PV with General Loads

If a commercial building has a PV system primarily offsetting its own consumption, and the same transformer also feeds general building loads, it's harder to argue for the exception.


AHJ Interpretation

Ultimately, the Authority Having Jurisdiction (AHJ) has the final say. They may have a stricter interpretation of "industrial installation" that precludes PV, regardless of how well you meet the letter of the code.

Practical Considerations & Best Practices



Consult with the AHJ Early

Before designing a system relying on this interpretation, have a detailed discussion with the AHJ. Present your rationale clearly and be prepared to provide documentation supporting your position (e.g., a single-line diagram showing the transformer serving
only power generation equipment).

Document Everything

Keep meticulous records of your design calculations, conductor ampacities, OCPD ratings, and the justifications for considering the installation "industrial."

Err on the Side of Caution

If there's significant doubt about the AHJ's acceptance, consider alternative designs that don't rely on the 25-foot tap rule. Over-sizing conductors or using a different transformer configuration might be more conservative and less likely to be rejected.


NFPA 70E

Remember that regardless of your code interpretation, you must always comply with NFPA 70E standards for safe work practices when working on or near electrical equipment. This is particularly important in power generation installations.

In Summary:


While there's no definitive "yes" or "no" answer in the NEC, it is entirely possible for a solar PV installation to be considered an industrial installation for the purposes of 240.21(C) under very specific circumstances: when the installation is solely dedicated to power generation and the transformer serves ONLY power generation equipment and essential station service. However, AHJ approval is paramount, and a thorough understanding of the conditions outlined in 240.21(C)(3) is essential. Be prepared to make a strong, well-documented case to the AHJ.I am not an electrician; consult with a qualified professional and your local AHJ before implementing any electrical designs. Flag for review

Previous Question Next Question