Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Good example drawing?

User: Conrad

Asked on: Tuesday, August 26, 2025 at 5:43 pm EDT
Answered on: Tuesday, August 26, 2025 at 5:46 pm EDT

Question: I am trying to find a good example drawing I can use to explain the need for separate grounds and neutrals on a distribution system. I.E 120/208 5 wire, this is to teach an administrator who already knows everything. I expected to fire up google and just pick one, I wasn't so lucky. My own drawing abilities suck, and taking the time to learn CAD does not fit in my timeline. Thanks to anyone who knows of one I can use. The actual point I will be trying to show him is the effect of having multiple main bonding jumpers throughout the system.

Okay, I understand the challenge. It's tough explaining something fundamental to someone who thinks they already understand it! Let's focus on getting you a resource that highlights the dangers of multiple neutral-to-ground bonds in a distribution system. That's the key to demonstrating the need for separate, dedicated grounding and neutral conductors.Here's a strategy and some potential resources

Strategy:

1. Focus on a Visual Representation

The drawing needs to be clear and easily understandable. Avoid complex electrical schematics that require detailed knowledge.2.

Highlight Ground Fault Current Path

The drawing MUST clearly show the path of fault current when there's a short circuit to ground. This is where the problems of multiple bonding become obvious.3.

Show Unintentional Current on Ground Conductors

The drawing should illustrate how multiple neutral-to-ground bonds cause normal load current to flow on the ground conductors, which is dangerous.4.

Keep it Simple

The simpler the better. Use minimal components, just enough to illustrate the issue.5.

Use Analogies (Optional)

Sometimes, analogies can help. For example, comparing the ground and neutral conductors to separate "pipes" for electricity, with the ground pipe only for emergencies.

Potential Resources and How to Adapt Them (Since you can't CAD it yourself)



Search Terms

Use very specific search terms in Google Images. Try these:
"multiple neutral ground bonds drawing" "ground loop diagram neutral current" "stray current neutral ground" "objectionable current grounding" "single point grounding vs multiple point grounding electrical" (This might turn up diagrams from the data center/IT world that can be adapted to your needs).

Electrical Forums and Blogs

Search for discussions or articles on electrical forums (Mike Holt, Electrical Contractor Magazine, etc.). People often post simplified diagrams or illustrations in response to questions about grounding.


Mike Holt Enterprises

Often has good diagrams.

Eaton and SquareD websites

Also have good application notes and often explain similar concepts.


IEEE standards and papers

Have great, technical drawings, you may need to filter through quite a bit to find one.

How to Adapt Existing Drawings (Since you're not creating one from scratch)


Screenshot and Annotate

Find a drawing that's close to what you need. Take a screenshot, paste it into a basic image editor (even MS Paint), and use the drawing tools to: Add arrows to show the flow of fault current and normal load current. Add text labels to point out the multiple neutral-to-ground bonds. Highlight the ground conductor and the unwanted current flow. Add text boxes to explain the consequences (e.g., "This current heats the ground conductor," "Increased risk of electrical shock").2.

Print and Draw

Print out a drawing and literally draw on it with a pen to clarify the current paths. Then scan or take a picture of the modified drawing.

Key Elements to Include in ANY Drawing You Use or Adapt



Source

Show a simplified representation of the utility transformer (or generator).


Service Entrance

Clearly mark the service entrance with the correct single main bonding jumper.

Subpanels

Show at least two subpanels. This is where you'll illustrate the
incorrect neutral-to-ground bonds.

Equipment Grounding Conductors (EGCs)

Show the EGCs running from each outlet/equipment back to the panel.

Fault Location

Indicate a point in one of the circuits where a fault to ground occurs (e.g., a short in an appliance).


Clear Current Paths

Use arrows (thick, bold arrows) to show: The intended path of fault current back to the source through the EGC and the correct main bonding jumper. The unintended path of fault current through the neutral conductor and then back through the EGC due to the multiple neutral-to-ground bonds. The path of normal load current that is now flowing on the grounding conductor

Example Drawing Description (What you're looking for)

Imagine a single-line diagram.1.

Top

A transformer winding labeled "Utility Transformer" with a center-tapped neutral.2.

Service Entrance

Lines run to a service entrance panel. This panel has a
single, clear connection between the neutral bus and the ground bus (the main bonding jumper).3.

Subpanel 1

A feeder runs to a subpanel.

Crucially, in this subpanel, the neutral bus is
also bonded to the ground bus (incorrectly).
An outlet is connected to a circuit in this subpanel. The outlet has a ground wire (EGC) that runs back to the ground bus in the subpanel. Show a fault (short to ground) in an appliance plugged into this outlet.4. Subpanel 2

Similar to Subpanel 1, but with another
incorrect neutral-to-ground bond.5.

Arrows

A thick arrow shows the intended path of fault current: from the fault in the appliance, through the EGC, back to the ground bus in Subpanel 1, through the incorrect bond to the neutral bus in Subpanel 1, back along the neutral conductor to the service entrance panel, and finally back to the transformer neutral. Another, equally thick arrow shows the unintended path: from the fault in the appliance, through the EGC, back to the ground bus in Subpanel 1, and then all the way back to the service entrance panel via the EGC (because it's connected to the neutral at Subpanel 1). Another arrow shows normal load current flow through the grounding conductor, in both subpanels, due to the multiple bonds.

Explanation to the Administrator:


Once you have a drawing, explain it like this:"This diagram shows why we need separate grounds and neutrals and why only one main bonding jumper is allowed. Imagine a short circuit happens in this appliance. We want that fault current to take the fastest and safest path back to the source so the breaker trips and cuts off the power. That path is through the equipment grounding conductor [point to the EGC] back to the main ground at the service entrance. However, when we have these extra connections [point to the incorrect bonds in the subpanels], some of that fault current (and even normal operating current) gets diverted onto the ground wires. This creates a shock hazard and can interfere with sensitive equipment, and even cause fires. It also prevents the breaker from tripping as quickly as it should, because the fault current is split across multiple paths."By visually demonstrating the multiple paths and the resulting unwanted current flow, you can make a convincing case, even to someone who thinks they already know it all. Good luck! Flag for review

Previous Question Next Question