Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: commercial dishwasher 60 amp 208v 3 phase or 100 amp 208v single phase GFCI requirements

User: Vincent Hetrick, Location: Florida

Asked on: Thursday, August 28, 2025 at 8:36 am EDT
Answered on: Wednesday, September 3, 2025 at 1:27 pm EDT

Question: good morning all, I need help with an upcoming job. I have a commercial dishwasher to bid that we can't seem to find a GFCI breaker for (if even needed). the dishwasher is 60 amp 3 phase 208v or 100 amp single phase 208 volt. does the NEC require GFCI protection for this application or will a standard breaker be sufficient?

Good morning! Let's break down the GFCI requirements for your commercial dishwasher.

Here's a breakdown of the situation and whether GFCI protection is required, based on the NEC (National Electrical Code)



General Rule: GFCI Protection for Dishwashers
The NEC generally DOES NOT require GFCI protection for permanently connected commercial dishwashers.

Why Not?
High-Power Equipment Exception

Commercial dishwashers are typically considered high-power, permanently connected equipment. GFCI breakers at these amperages are rare and often impractical for commercial use.

Focus on Grounding and Bonding

The primary focus in these installations is proper grounding and bonding to ensure a low-impedance path to ground. This allows a fault current to quickly trip the standard breaker and de-energize the circuit, preventing a shock hazard.


Commercial/Industrial Setting

GFCI protection requirements are sometimes less stringent in commercial and industrial settings compared to residential, based on the assumption of more trained maintenance staff and stricter safety protocols.

Important Considerations & Best Practices
1. Local Codes and AHJ (Authority Having Jurisdiction)

This is

THE MOST IMPORTANT POINT
. Always check with your local electrical inspector or AHJ. They have the final say and can impose requirements beyond the NEC. Some jurisdictions may have amended the NEC or have specific interpretations that mandate GFCI protection in your situation, even if the NEC doesn't. Call or email the inspector and ask if there are any local amendments regarding commercial dishwashers and GFCI protection. Document their response for your records.2. Manufacturer's Instructions



Review the dishwasher's installation manual.
The manufacturer might specify GFCI protection, even if the NEC doesn't explicitly require it. This is rare, but always check.3. Location of the Dishwasher

If the dishwasher is installed in a readily accessible location, or near water, or in a location where accidental contact with water is likely, it is always wise to consult the AHJ.4.

Proper Grounding and Bonding (Crucial)

Ensure the dishwasher is properly grounded and bonded according to NEC Article 250. This is paramount for safety. Use appropriately sized grounding conductors, and ensure all metal parts of the dishwasher are bonded together and connected to the grounding system. Pay special attention to bonding water pipes if they are metallic and connected to the dishwasher.5.

Leakage Current Testing

After installation, it's a good practice to perform a leakage current test on the dishwasher. This test measures the amount of current flowing to ground under normal operating conditions. Excessive leakage current can indicate a potential problem and might suggest the need for additional protection (though not necessarily GFCI).6.

Consider Additional Safety Measures

While GFCI might not be required, you could consider other safety measures, such as:

Regular Inspections

Implement a schedule for regular visual inspections of the dishwasher and its electrical connections.


Employee Training

Train employees on safe operating procedures and how to identify potential hazards.

Emergency Shut-Off

Install a readily accessible emergency shut-off switch near the dishwasher to quickly de-energize the circuit in case of an emergency.

In summary

NEC generally doesn't require GFCI for permanently connected commercial dishwashers.

Contact your local electrical inspector (AHJ) to confirm if there are any local requirements.
This is the most important step. Review the manufacturer's installation instructions.* Ensure proper grounding and bonding.

How to bid


Quote the standard breaker installation.
2. Add a line item: "GFCI Breaker (if required by AHJ)." Price this separately so the client knows the additional cost if the inspector mandates it. Research the cost of a 60A or 100A 208V 3-phase GFCI breaker (if available) so you're prepared. They are VERY expensive, if they exist. 100A single phase breakers are commonly available but still expensive.3. Include a note in your bid: "Price does not include GFCI protection unless mandated by the local Authority Having Jurisdiction. Confirmation of local code requirements will be obtained prior to installation."By following these steps, you'll be able to provide an accurate and safe installation while meeting all applicable code requirements. Good luck with the bid! Flag for review

Previous Question Next Question