User: fastline, Location: midwest usa
Asked on: Friday, August 29, 2025 at 2:08 pm EDT
Answered on: Wednesday, September 3, 2025 at 1:31 pm EDT
Question: I got a call but have not yet been onsite. Customer is on rural 1P. He requested 400A, which is broke down to 200A to a home and 200A to his shop. This is all being fed with a 50kva pad transformer. Complaint is when starting and running a big air compressor, it will struggle severely. When running, the current on the line is 130A. Obviously inrush has to be evaluated here but I am wondering how hard you can pull on that transformer before significant voltage drop occurs? I am sort of suspecting primary sag but again I have not been onsite yet. I do know after a struggle to start, the 200A main break has opened a couple times. To me that sounds like severe voltage drop where the load cannot accelerate, causing high current long enough to open. Just a hunch.I've generally figured that 150% OL is fine for a transformer and I know POCOs push them extremely hard feeding homes.
Okay, you're right to be suspicious. Here's a breakdown of how to approach this situation and the potential issues
Key Concerns & Initial Analysis
1. Transformer Capacity
A 50 kVA transformer on 1-phase service is already potentially undersized. Let's calculate the rated current it can supply at 240V: kVA = (Volts Amps) / 1000 Amps = (kVA 1000) / Volts Amps = (50 1000) / 240 = ~208 Amps.You're already pulling 130A with the compressor running. That leaves very little headroom for inrush. While brief overloads are common on transformers, sustained loads this high, with significant inrush, are a recipe for voltage sag and premature transformer failure.2.
Inrush Current
Air compressors are notorious for very high inrush currents, often 3-7 times the running current. Let's assume a modest inrush of 4x the running current of the compressor: Inrush = 130A 4 = 520AEven if that inrush only lasts for a second or two, it's way beyond the transformer's capability. The transformer will experience significant voltage sag under that load.3.
Voltage Drop
Voltage drop is your primary suspect. The fact that the 200A breaker trips after struggling to start the compressor strongly suggests: The inrush causes a huge voltage drop. The compressor motor struggles to overcome inertia, drawing excessive current for a prolonged period. This sustained high current, even though it might be below the inrush peak, exceeds the breaker's trip curve for a sufficient duration, causing it to open.4.
Breaker Size
The 200A breaker opening indicates to me that the 130A running current is on the home main. The customer is likely tripping the service from running loads inside of the home, and his large compressor. This can be an issue with inrush, but the more likely cause of this breaker trip is the sum of all loads in the house while his compressor is running.5.
Primary Sag
While primary voltage sag is possible, it's less likely unless the utility's infrastructure in that rural area is already heavily loaded. If you measure significantly low voltage before the transformer even when the compressor isn't running, then primary sag becomes a major suspect.6.
Rural 1P Service Limitations
Rural single-phase services often have limitations on transformer size and voltage regulation. The distribution lines may be longer, smaller gauge, and less robust than in more densely populated areas.
On-Site Investigation Steps
Before doing anything else, inform your supervisor or the POCO that you believe the 50 kVA transformer is undersized for the requested service.1. Measure Voltage
No Load
Measure the voltage at the transformer secondary (both legs) before the compressor is running. This establishes your baseline.
Running
Measure the voltage at the transformer secondary and at the 200A breaker while the compressor is running. Note the voltage at both points.
Starting
If possible (and safe), measure the voltage during compressor startup. Use a meter with a "Min/Max" recording function to capture the lowest voltage during the inrush. Also measure the voltage at the load. This could be tricky and potentially dangerous if the inrush trips the breaker too quickly.2.
Measure Current
Running
As you've already done, measure the current on each leg of the service while the compressor is running.
Starting
If possible, use a clamp meter with a "Peak Hold" function to try to capture the inrush current. Be aware that many meters struggle to accurately capture very short-duration peaks.3.
Transformer Health
Visual Inspection
Look for signs of overheating on the transformer (discoloration, bulging, oil leaks).
Temperature
Carefully check the transformer's temperature with an infrared thermometer. Compare to the manufacturer's specifications (if available).4.
Wiring
Conductor Size
Verify that the conductors from the transformer to the main panel are adequately sized for 400A service. Undersized conductors will exacerbate voltage drop.
Connections
Check all connections for tightness and corrosion at the transformer, meter base, and main panel. Loose or corroded connections create resistance and increase voltage drop.5.
Document Everything
Record all voltage, current, and temperature readings, along with any observations (e.g., condition of the transformer, wiring, connections). Take pictures.
Possible Solutions (and likely recommendations)1. Increase Transformer Size
This is the most likely solution. A larger transformer (75 kVA, 100 kVA, or even larger) is probably needed to handle the 400A service and the compressor's inrush. This will require coordination with the utility. The utility will likely require the customer to pay for all upgrades needed for the proper service.2.
Soft Starter
Install a soft starter or variable frequency drive (VFD) on the air compressor. These devices gradually ramp up the motor, significantly reducing inrush current.3.
Reduced Voltage Starter
Similar to a soft starter, this uses autotransformers or resistors to reduce the voltage applied to the motor during startup.4.
Power Factor Correction
While not the primary issue, improving the power factor of the compressor motor can slightly reduce the overall current draw.5.
Load Shedding
Implement a load shedding system that prevents the compressor from starting if other large loads in the house are already running. This is more complex to implement.
Important Considerations Utility Coordination
You must work closely with the utility throughout this process. They own and maintain the transformer and primary distribution system. Any changes to the transformer or service size will require their approval and involvement.
NEC Compliance
Ensure that all wiring and equipment meet the requirements of the National Electrical Code (NEC). Pay close attention to conductor sizing, overcurrent protection, and grounding.
Customer Communication
Keep the customer informed about the problem, the proposed solutions, and the costs involved. Explain that the original setup was likely inadequate for their needs.
Safety
Always prioritize safety when working with electrical equipment. De-energize circuits before working on them whenever possible. Use appropriate PPE (personal protective equipment).
In summary, your initial hunch is likely correct. A 50 kVA transformer is likely undersized for the application. The inrush current of the air compressor is causing excessive voltage drop, leading to the breaker tripping. A larger transformer and/or a soft starter are likely needed to resolve the issue. Flag for review