Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Working Space for panel replacement

User: trevorm, Location: Central Washington

Asked on: Wednesday, September 3, 2025 at 12:35 am EDT
Answered on: Wednesday, September 3, 2025 at 1:41 pm EDT

Question: This panel needs to be replaced with a larger panel to make room for some new circuits with AFCI/GFCI breakers. Now working space is a concern since it is right up against the wall on the left side. I would really like to avoid moving the panel to the right and all that's involved with that. I'm going to put a call into the inspector as well but I'd like to hear some thoughts on move it or leave it as is. What would you do?

Okay, let's break down the considerations for your electrical panel replacement, focusing on working space and avoiding a panel move

Understanding the Problem
Need for Larger Panel

You need more breaker space to accommodate new AFCI/GFCI circuits. AFCI/GFCI breakers tend to be physically larger than standard breakers.


Limited Working Space

The existing panel is tight against the wall on the left, creating a confined area to work on the panel.

Desire to Avoid Moving

You understandably want to avoid the complexity and cost of shifting the panel physically to the right.

Key Considerations
1. NEC (National Electrical Code) Requirements for Working Space

This is the most crucial factor. The NEC dictates the
minimum clear working space required in front of electrical equipment that is likely to need examination, adjustment, servicing, or maintenance while energized. This includes panelboards. The specific requirements depend on the voltage to ground, the condition of the space opposite the panel (e.g., grounded surface, insulated surface, etc.), and whether the panel is likely to be worked on while energized.

Depth (Distance from the Panel)

This is the distance you need to be able to stand in front of the open panel. It's based on voltage to ground and conditions described in 110.26(A)(1).

Width

The working space must be at least 30 inches wide
or the width of the equipment, whichever is greater. This width must allow for at least a 90-degree opening of the panel door or cover. It's also not permitted to encroach on the dedicated equipment space in 110.26(E)(1).

Height

The working space must be clear from the floor or platform to a height of 6 1/2 feet (1.98 m) or the height of the equipment, whichever is greater.
2.


Larger Panel Dimensions

A larger panel will be physically wider and potentially taller than your existing panel. This can exacerbate the working space issue.3.

Wire Length

The existing wiring likely has very little extra slack. If you move the panel even a small amount, you could run into situations where wires are too short to reach the breakers in the new panel location. This is a major headache and can lead to the need for splicing (which introduces its own complexities and code requirements).4.

Complexity of Moving

Moving the panel means: Disconnecting all circuits. Extending (or replacing) every wire. Creating a new mounting surface. Potentially dealing with conduit runs and securing them to the new location. Making new connections to the service entrance conductors. Re-labeling circuits. Inspection.5.

Panel Orientation

Consider the orientation of the new panel. Will the new panel be slightly taller or wider than the current panel? This could change the space requirements around it.

What I Would Do (Considerations & Steps)
1. Measure, Measure, Measure



Panel Dimensions

Accurately measure the exact dimensions (width, height, depth) of the current panel. Note where the incoming service wires enter the panel (top, bottom, side).

Working Space

Measure the clear working space in front of the
closed panel. Then, imagine the panel door fully opened and measure again. How close is it to the wall on the left? Is it at least 30" wide or the width of the panel?

Wire Slack

Carefully open the existing panel and visually assess the amount of slack in the wires. This is critical. Can you easily move the panel a few inches in any direction without straining the wires? If the wires are tight, moving is going to be far more complex.

Turn off the main breaker before opening the panel.
Area in Front of Panel

Is there anything blocking the space in front of the panel? Any cabinets or shelving that needs to be moved?2.

Determine NEC Working Space Requirements



Voltage to Ground

This is typically 120V (single-phase) or 208V (three-phase) in a residential setting.

Condition 1, 2, or 3

Look at what's directly
opposite the panel when you're working on it. Condition 1: Exposed live parts on one side and grounded parts on the other side of the working space with no insulation between them. Condition 2: Exposed live parts on one side and grounded parts on the other side of the working space with insulation between them. Condition 3: Exposed live parts on both sides of the working space. Condition 4: Exposed live parts on one side and no live parts on the other side of the working space.

Consult NEC Table 110.26(A)(1)

This table provides the minimum working space depth (distance from the panel) based on the voltage and the condition.

30-Inch Width Rule

Remember the 30-inch width requirement.3.

Panel Selection



Breaker Spaces

Calculate the total number of circuits you need now and in the future. Consider that you might want to add circuits later. Oversize slightly to avoid future problems.

Panel Type

Stick with a reputable brand (Square D, Eaton, Siemens). Look for a panel that is designed to accommodate the AFCI/GFCI breakers that you intend to use. Some panels are designed with specific breaker slots that make it easier to install these types of breakers.


Physical Size

Get the exact dimensions of the new panel you're considering.4.

Simulate the New Panel

Using cardboard or a similar material, create a mock-up of the new panel's dimensions. Hold it up in place of the existing panel to visualize how it will impact the working space. Open the mock-up panel door to see if it interferes with the wall.5.

Potential Solutions (If Working Space is Insufficient)



Slightly Larger Panel in the Same Location

If you can find a slightly larger panel that
just fits within the existing space and meets the working space requirements, this is the easiest solution.

Flush Mounting (If Possible)

If the panel is surface-mounted, consider whether it can be flush-mounted into the wall. This could buy you a few inches of working space. Be aware of fire-stopping requirements for penetrations of fire-rated walls.

Relocating Obstructions

Can you move anything that is restricting access in front of the panel? Even moving something a few inches can make a big difference.


Moving the Panel to an Adjoining Wall

Maybe moving the panel to the connecting wall is a better option as this might allow for easier work.

Subpanel

Could you potentially install a subpanel in a more accessible location and move some of the existing circuits to it? This would free up space in the main panel.6.

Speak with the Electrical Inspector

Before you commit to anything, discuss your plan with the electrical inspector. They can provide valuable insights and ensure that your solution meets local code requirements. Document their feedback.

In summary



Prioritize Safety and Code Compliance

The NEC is there to protect you and others. Don't cut corners.

Thorough Assessment

Measure everything carefully. Understand the NEC requirements.


Seek Expert Advice:
Talk to the electrical inspector before you start any work.It sounds like you're approaching this carefully, which is exactly what you should do. Good luck! Flag for review

Previous Question Next Question