User: joji, Location: North east
Asked on: Wednesday, September 3, 2025 at 12:18 pm EDT
Answered on: Wednesday, September 3, 2025 at 1:43 pm EDT
Question: The house was built late 1800's. It was converted to a boarding house mid/ late 1900's. There are smoke detectors in all the hallways ave they are connected together. They are hardwired in that they talk to each other, but there is no power from the service. They are running off the 9v dc battery. After investigating, I found a transformer near the panel that says low voltage smoke detectors. On the line side is 12/2 bx, On the load side is a low voltage cable - type I've never seen before. Made of metallic shealth but very flexible, not breakable, probably 16or 18awg.So, my questions are: does the NEC require two power sources in this scenario? Does it actually require 120 v a/c or does it just require all common area smokes to be wired in tandem? Would it pass Inspection as is, powered by battery but wired in tandem?Next, has anyone ever seen low voltage smoke detectors? Was that ever a thing? Im curious why this was constructed this way to begin with.
Okay, let's break down your smoke detector situation.
Understanding the NEC Requirements (Generally) Dual Power Source
The NEC (National Electrical Code) generally requires smoke detectors to have both a primary power source (usually 120V AC) and a secondary power source (battery backup). This is to ensure they function even during a power outage. Specific requirements can depend on the year the house was built and local amendments, so check with your municipality.
Interconnection
The NEC requires that smoke detectors in dwellings, when more than one is required, be interconnected. This means that if one alarm sounds, all the alarms sound.
Inspection
A smoke detector system powered solely by batteries and interconnected likely would not pass a modern inspection, especially in a boarding house scenario. The code emphasizes the need for a reliable, primary power source.
Local Amendments
Remember that local jurisdictions (city, county, etc.) often amend the NEC. So, what's code-compliant in one area might not be in another.
Always consult your local building and fire departments for specific requirements.Your Specific Situation1. Boarding House
Because this is a boarding house, not a single-family dwelling, the requirements are typically more stringent. Boarding houses are considered residential occupancies but have a higher risk profile.2.
Transformer
The presence of a transformer labeled "low voltage smoke detectors" strongly suggests that the original intent was to power the smoke detectors from a low-voltage AC source. The fact that it's currently disconnected and running only on batteries is a red flag.3.
Unusual Cable
The flexible metallic sheath cable you describe could be various things. One possibility is that it's a type of flexible metal conduit (FMC) but on a smaller scale than typically seen. Another possibility is that it is a proprietary cable.4.
Low Voltage Smoke Detectors
Yes, low-voltage smoke detectors were (and still are) a thing. They are often used in commercial fire alarm systems because they can use smaller gauge wiring over longer distances and can be connected to a central control panel. It's not as common in residential settings.
Possible Explanations for the Setup Early Fire Alarm System
The house may have been converted to a boarding house and equipped with an early fire alarm system utilizing low-voltage detectors before more widespread adoption of 120V AC smoke detectors in residential settings.
Cost Savings
Using low voltage smoke detectors can save on installation costs, as lower voltage wires are easier to run and can often be installed without conduit (depending on the code).
Professional Installation
Low voltage systems are usually installed by qualified electricians or fire alarm system installers.
Recommendations1. Contact a Qualified Electrician or Fire Alarm Technician
The most important thing to do is to have a qualified electrician or a fire alarm technician inspect the entire system. They can: Properly identify the type of low-voltage cable. Test the transformer to see if it's functioning correctly. Determine why the original low-voltage system isn't working. Assess whether the existing detectors are still functional and compliant with current standards. Make recommendations for upgrading or replacing the system to meet current NEC and local code requirements.2.
Consult Local Building and Fire Departments
Contact your local building and fire departments to inquire about specific code requirements for smoke detectors in boarding houses in your area.3.
Consider Upgrading
Depending on the age and condition of the existing system, it might be more cost-effective to replace it with a modern, code-compliant system. This could involve: Installing 120V AC smoke detectors with battery backup that are interconnected. Installing a modern fire alarm system with a control panel, smoke detectors, and other devices like pull stations and notification appliances.
In summary: This setup is likely non-compliant with current codes, particularly for a boarding house. Get professional help to evaluate and upgrade the system for safety and compliance. Flag for review