Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Eaton/Crosshinds Emergency Bug Eye Light ELPSM2 K50

User: kjroller, Location: Dawson Mn

Asked on: Wednesday, September 3, 2025 at 2:18 pm EDT
Answered on: Wednesday, September 3, 2025 at 2:29 pm EDT

Question: In the industrial facility I work in we have many of the hazardous area emergency lights for exit lighting in our classified areas. I have replaced several of these boards and batteries in the last year many of them more than once. The issue is it seems like these boards only last like 6 months max and then I have a repeat problem they run about 3500$ a piece has anyone else experienced these problems with these lights and if so do they have a warranty. They are really a pain to replace so I would like to hear some feedback if anyone else has worked with them or good replacements please and thank you!

Wow, $3500 per board is a significant expense, and frequent replacements are a serious problem. Here's a breakdown of possible causes, troubleshooting steps, and considerations for replacements and warranties

Possible Causes for Frequent Emergency Light Board Failures in Hazardous Areas:
Environmental Factors



Extreme Temperatures

Hazardous areas can experience wide temperature swings, and electronics are sensitive to heat and cold. Are these lights exposed to direct sunlight or extreme cold?

Vibration

Industrial environments often have vibrations that can loosen connections or damage components on the circuit board.


Dust/Corrosion

Hazardous areas often have specific dusts or corrosive substances that can infiltrate the light fixture and damage the electronics. Are these lights properly sealed? Are you using the correct type of explosion-proof enclosure for the specific hazard present?

Humidity

Moisture ingress can lead to corrosion and short circuits on the board.


Power Quality



Voltage Fluctuations

Spikes, sags, and surges in the power supply can damage sensitive components. Industrial power can be "dirty."


Harmonic Distortion

High harmonic content in the power can overheat components on the board.

Grounding Issues

Poor grounding can lead to stray currents and electrical noise that damages the boards.


Battery Issues (related to board failures)



Incorrect Battery Type

Are you using the exact battery specification recommended by the manufacturer (voltage, chemistry, capacity)?


Overcharging/Undercharging

A faulty charging circuit on the board can damage the battery and, in turn, put stress on the board.

Battery Age

Batteries have a limited lifespan. If the batteries are old and failing, they can draw excessive current during charging, potentially damaging the charging circuit on the board.


Manufacturing Defects



Poor Quality Components

The manufacturer might be using substandard components on the boards.


Poor Manufacturing Processes

Poor soldering, inadequate quality control, or improper handling during assembly can lead to premature failures.

Incorrect Installation



Wiring Errors

Incorrect wiring can damage the board or create a short circuit.

Over-tightening Connections

Over-tightening screws can damage the board or its components.


Compliance Issues



Hazardous Area Classification

Ensure the lighting fixtures are rated for the specific hazardous area (Class, Division/Zone, Gas Group, Temperature Code). Using an incorrect fixture can lead to premature failure or, worse, a safety hazard.

Troubleshooting Steps


Document Everything

Keep a detailed log of each failure, including: Date of installation Date of failure Specific symptoms (e.g., completely dead, flickering, battery not charging) Ambient conditions (temperature, humidity, presence of dust/corrosives) Power supply voltage readings (at the fixture) Battery voltage readings (before and after charging) Any visual signs of damage (burnt components, corrosion)2.

Check Power Quality

Use a power quality analyzer to monitor the voltage, current, harmonics, and transients at the light fixture. Identify any anomalies in the power supply. Verify the grounding is adequate.3.

Inspect Installation

Carefully review the installation instructions to ensure they were followed correctly. Check for loose connections or damaged wiring. Verify the light fixture is properly sealed against the environment.4.

Examine Failed Boards

Visually inspect the failed boards for any signs of damage: Burnt or discolored components Corrosion Cracked solder joints Swollen capacitors5.

Battery Testing

Test the batteries using a battery analyzer to determine their capacity and internal resistance. Replace any batteries that are below specifications. Verify the charging voltage and current from the board are within the battery's specifications.6.

Consult with a Qualified Electrician or Engineer

Bring in a professional experienced in hazardous area electrical systems to help diagnose the problem. They can perform more in-depth testing and analysis.

Warranties



Check the Manufacturer's Warranty

Contact the manufacturer of the emergency lights to inquire about their warranty policy. Most manufacturers offer a warranty against defects in materials and workmanship, but the length of the warranty can vary. A one-year warranty is typical, but some offer longer warranties. You've been replacing them frequently, so you should be well within any reasonable warranty period. A $3500 board SHOULD have more than a year's warranty.


Keep Records

Maintain records of all purchases, installations, and failures to support any warranty claims.

Potential Replacements and Considerations



Research Reputable Manufacturers

Look for manufacturers with a proven track record of producing reliable hazardous area lighting. Consider brands that are well-regarded in the industry.


Consider LED Technology

LED-based emergency lights are generally more energy-efficient and have a longer lifespan than traditional lighting technologies. They also often have better vibration resistance.

Check for Certifications

Ensure the replacement lights are certified for the specific hazardous area classification in your facility (e.g., UL, ATEX, IECEx). Confirm the markings on the fixture match the classification requirements for your location.


Consider Self-Testing Features

Some emergency lights have self-testing features that automatically test the battery and charging system on a regular basis. This can help identify potential problems before they lead to a complete failure.

Get Multiple Quotes

Obtain quotes from several different suppliers before making a purchase.


Pilot Program

Before replacing all the lights, consider installing a small number of replacement lights from a different manufacturer as a pilot program. This will allow you to evaluate their performance and reliability in your specific environment.

Additional Tips



Review the Hazardous Area Classification

Ensure that the hazardous area classification for your facility is still accurate. Changes in processes or materials can affect the classification.


Preventive Maintenance:
Implement a regular preventive maintenance program for the emergency lights, including visual inspections, battery testing, and cleaning.Given the high cost and frequent failures, it's crucial to investigate the root cause thoroughly. Start by documenting everything, checking the power quality, and inspecting the installation. Contact the manufacturer to inquire about the warranty and explore alternative lighting solutions from reputable suppliers. Don't hesitate to bring in a qualified electrician or engineer to assist with the troubleshooting process.Good luck! Flag for review

Previous Question Next Question