User: Chanceelectric, Location: Iowa
Asked on: Wednesday, September 3, 2025 at 3:55 pm EDT
Answered on: Wednesday, September 3, 2025 at 3:55 pm EDT
Question: I’m relocating a electric panel inside of a home because of clearance issues in front of the panel. Where I’d like to move it to I’d be directly under a window. It’s a non-egress type window. Is there anything in the code that would prevent me from running it here? I don’t know if the inspector would classify that as something being 6 foot above the panel.
Okay, let's break down the potential code issues with placing an electrical panel directly under a non-egress window inside a home. While there isn't a specific rule prohibiting a panel under a non-egress window, there are several general rules that could come into play and cause an inspector to reject the location.
Key Considerations & Potential Code Issues
Working Clearance (NEC 110.26(A))
This is the most likely area where you'll encounter problems. The NEC specifies clear working space in front of electrical equipment likely to require examination, adjustment, servicing, or maintenance while energized. This space needs to be clear and unobstructed.
Depth
The depth of the working space depends on the voltage to ground and the conditions present (e.g., exposed live parts on one side and grounded parts on the other side). Typically, for a residential panel (120/240V), you're looking at a minimum of 3 feet. If there are exposed live parts on both sides or exposed live parts opposite grounded parts (like a concrete wall), it could be 3.5 or even 4 feet.
Width
The width of the working space must be the width of the equipment or 30 inches, whichever is greater. This is centered on the equipment.
Height
The working space must extend from the floor or platform to a height of 6 1/2 feet (78 inches) or the height of the equipment, whichever is greater.
The Window Issue
This is where the problem likely arises. An inspector could argue that the window sill, the window itself, and potentially even the window trim obstruct the required working space, even if you can physically stand in front of the panel. They might argue that it impedes safe access for servicing the panel.2.
Dedicated Equipment Space (NEC 110.26(E))
This section requires that the space above and below the panel be kept clear of foreign systems. The code prohibits any piping, ductwork, or other equipment foreign to the electrical equipment to be located in the space above or below the equipment.
The Window Issue
While the window itself isn't piping or ductwork, an inspector could argue that it's "other equipment foreign to the electrical equipment." This is less likely than the working clearance argument, but it's possible.3.
Headroom (NEC 110.26(A)(3))
Headroom requirements are part of the working space rules, as described above.
The Window Issue
If the bottom of the window frame is less than 6 1/2 feet (78 inches) above the floor, this will definitely be a problem.4.
Environmental Conditions
The location should be dry and protected from the elements. A window, even a non-egress one, could be a source of moisture or drafts, especially if it's an older window. The concern is corrosion or water damage to the electrical panel.
Why It Might Be Okay (But Still Risky)
Very High Window
If the bottom of the window is significantly higher than 6 1/2 feet, and the sill is minimal, and the window doesn't overhang the panel excessively, you might be able to argue that the working clearance isn't compromised.
Small Panel
A very small panel (e.g., a subpanel) might be easier to fit within the working clearance requirements.
What to Do
Consult Your Local Inspector FIRST
This is the most important step. Explain your plan before you do any work. Ask if they would allow it, and what their specific concerns would be. A picture or sketch can be very helpful. Get their answer in writing, if possible (though that's often difficult). Their interpretation of the NEC is what matters in your jurisdiction.2.
Careful Measurements
Accurately measure the height of the bottom of the window, the depth of any sill, and the overall dimensions of the window. Make sure you have the required working clearances.3.
Consider Alternatives
Is there another location that would be less problematic? Sometimes moving the panel a few feet can make a big difference.4.
Documentation
Keep records of all your measurements and any communications with the inspector.5.
Be Prepared to Compromise
The inspector might require modifications to the plan, such as moving the panel slightly to the side, or installing a smaller panel.
In summary, while there's no specific code prohibition* against putting a panel under a non-egress window, the working clearance and dedicated equipment space requirements of the NEC are likely to be the biggest hurdles. Your best bet is to discuss your plans with your local electrical inspector BEFORE you start any work. Good luck! Flag for review