Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: NM in conduit

User: guschash, Location: Ohio

Asked on: Thursday, September 4, 2025 at 10:58 am EDT
Answered on: Saturday, September 6, 2025 at 12:12 pm EDT

Question: I have to run #6 NM through the basement 50 feet through block transition to PVC for 30 feet up in garage panel. Can I run the #6 NM all the way? Or should I run THWN through conduit to garage?

Okay, let's break down the code-compliant way to handle this wiring scenario.

Understanding the Situation



#6 NM Cable

You have #6 NM-B cable (Romex) running through your basement.


Basement (Block)

It's running 50 feet through a block (likely concrete block) basement wall.

Transition

You need to transition to a 30-foot run up to your garage panel.


Garage

The garage environment can introduce different considerations (potential physical damage, moisture).

Code Considerations & Best Practices


NM Cable Limitations

NM-B cable is

not
permitted in wet or damp locations, or where subject to physical damage (NEC 334.10). Direct burial in masonry or concrete is also not permitted.
2. Physical Protection

NM-B cable needs protection where subject to physical damage.3.

Transitioning

This is the critical point. You can't simply run the NM-B exposed up the garage wall, especially if it's likely to be damaged.4.

THWN/THHN in Conduit

Using THWN or THHN conductors inside conduit is a common and code-compliant method for runs in potentially exposed or damp/wet locations, and for physical protection.

The Recommended Solution: Transition to THWN/THHN in Conduit


Here's the most likely code-compliant and practical approach: Basement Run (NM-B)

If the block walls are dry and the NM-B is adequately supported (stapled properly every 4.5 feet), you can run the NM-B along the block wall for the 50 feet as long as it's not in direct contact with the concrete or masonry and is protected from physical damage. You could use cable ties or insulated staples to secure it. If the block wall is damp or has any moisture concerns, you MUST protect the NM-B. Run it inside a conduit (PVC or EMT) where it's against the block wall.

Transition Point

At the point where you want to go from the basement to the garage, install a junction box. Make sure the junction box is accessible. Inside the junction box, make the transition from the NM-B cable to individual THWN/THHN wires. Use appropriately sized wire connectors (wire nuts or similar) listed for the purpose. From the junction box, run conduit (PVC or EMT) up to the garage panel.

Garage Run (THWN/THHN in Conduit)

Run the THWN/THHN wires inside the conduit. Terminate the conduit directly into the garage panel. Use the correct size conduit. For #6 THWN/THHN, you'll typically need at least 3/4" conduit. (Check conduit fill charts to be certain). Make sure the conduit is securely supported along the wall.

Important Considerations and Specific Steps


Wire Size and Ampacity

Verify that #6 AWG wire is appropriate for the circuit's amperage. #6 copper THWN/THHN is typically rated for 55 amps (check your local codes and the ampacity rating stamped on the wire insulation). Ensure this matches the circuit breaker size.2.

Grounding

Ensure that the grounding conductor is properly sized and connected throughout the entire run. The grounding conductor should run inside the conduit along with the THWN/THHN conductors. Typically, a #10 copper ground wire is sufficient for a #6 circuit.3.

Conduit Type



PVC

PVC is suitable for damp locations and is relatively easy to work with.


EMT (Electrical Metallic Tubing)

EMT provides better physical protection and can be used if you're concerned about impacts or damage. It requires proper grounding techniques (bonding).4.

Conduit Fill

Don't overcrowd the conduit. Consult conduit fill charts in the NEC or online to ensure you're within the allowed fill percentage. Generally, you want to stay below 40% fill.5.

Local Codes and Permits



Crucially important

Check with your local electrical inspector's office before starting any work. They may have specific requirements or amendments to the NEC that you need to follow. Also, a permit is likely required.6.

Professional Assistance

If you're not comfortable working with electrical wiring, it's always best to hire a qualified electrician. Electrical work can be dangerous if not done correctly.

Why This Approach Is Best



Code Compliance

It addresses the NM-B's limitations and ensures it's properly protected.


Safety

It reduces the risk of electrical shock or fire.

Durability

The conduit protects the wires from physical damage.


Future Flexibility

Conduit allows you to easily replace or upgrade the wiring in the future.

In summary: Run the #6 NM-B in the basement only if it's a dry location and protected from damage. Transition to individual #6 THWN/THHN wires inside conduit at a junction box before the run to the garage panel. Always consult with your local electrical inspector to ensure compliance with all applicable codes.
Flag for review

Previous Question Next Question