User: thisisausername, Location: Here
Asked on: Friday, September 5, 2025 at 8:36 pm EDT
Answered on: Saturday, September 6, 2025 at 12:15 pm EDT
Question: I will be inserting a transfer switch between my home's meter base and load center. The transfer switch will take over main breaker duty and function as the service disconnect, with the load center acting only as a sub panel. The load center and transfer switch will be in the same structure and room.In this scenario, must I relocate the two grounding electrode conductors (200A service) from the load center (now a sub panel) to the transfer switch's (now the service disconnect's) ground bar? The load center will of course no longer have neutral bonded while the transfer switch will, and the load center's ground bar will be connected to the transfer switch's ground bar. Physically, it seems almost the same to me whether the GECs are relocated or not, with the only difference being that the service disconnect's (now transfer switch's) ground bar has one physical path to those two electrodes instead of two.The transfer switch's installation manual does not mention this at all, but my instinct is that I would need to relocate the GECs. Section 250 is quite long and is taking some time for me to break down and decipher. All I've been able to find via Google is this PDF from a state in which I don't live, and its answer implies that whoever wrote it doesn't even understand that neutral shouldn't be bonded at the sub panel.
You are correct, your instinct is right. You absolutely must relocate the grounding electrode conductors (GECs) to the grounding bar in the transfer switch. Here's why: Service Disconnect
The transfer switch is now acting as the service disconnect. The NEC (National Electrical Code) requires the grounding electrode system to be connected to the service disconnecting means.
Bonding and Grounding Hierarchy
The entire grounding and bonding system is designed to provide a low-impedance path for fault current back to the source. This is essential for tripping circuit breakers and clearing faults quickly, which is vital for safety. The hierarchy is:1. Grounding Electrode System (GECs to rods, water pipe, etc.)2. Service Equipment (where neutral is bonded)3. Equipment Grounding Conductors (connecting non-current carrying metal parts)
NEC Violations if you don't
250.24(A)(1)
"Grounding of Alternating-Current Systems. Alternating-current systems that are grounded as specified in 250.20 shall be grounded in the following manner: (1) Electrical System Grounding Connection. A premises wiring system shall be grounded at the service disconnecting means as specified in 250.24(A)(2) or at the source of a separately derived system.
250.24(C) (Paraphrased)
You have to connect to one of the grounding electrodes described in 250.52.
Why it matters
You need a continuous path for fault current from the subpanel back to the source. If a fault occurs in an appliance connected to the load center, the fault current needs to return to the transformer through the ground wire to trip the breaker. Keeping the GECs at the load center would create a parallel path, with current flowing through the grounding electrode system back to the source. This is undesirable as current is best kept in a low impedence, dedicated ground wire.
Practical Steps and Considerations
Relocate GECs
Move the grounding electrode conductors from the ground bar in your load center to the ground bar in the transfer switch. Ensure they are properly sized according to NEC 250.66 and properly terminated.
2.
Isolate Neutral
As you mentioned, and crucially, you must remove the neutral-to-ground bond in your load center. This is done by removing the bonding screw or strap that connects the neutral busbar to the enclosure. The load center's neutral bus should only be connected to the neutral bus in the transfer switch via the feeder conductors.3.
Feeder Conductors
Run four wires between the transfer switch and the load center: two hots, a neutral, and a ground.4.
Proper Grounding Conductor Size
Verify that the equipment grounding conductor (ground wire) running from the transfer switch to the load center is sized appropriately according to NEC 250.122. This conductor is essential for providing a low-impedance path for fault current.
5.
Torque to Spec
Use a torque screwdriver or wrench to properly tighten all connections. Loose connections can cause heat, voltage drop, and ultimately failure.6.
Inspection
Have a qualified electrical inspector review your work. This is not just a good idea, but likely a requirement in your jurisdiction. They can verify that everything is installed correctly and safely.
In summary, treat the load center exactly like a subpanel fed from the transfer switch. The transfer switch is the service equipment, so all grounding electrode conductors must terminate there. Failure to do this creates a dangerous situation and violates the NEC. Flag for review