Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Should you derate twice for two separate conditions?

User: Sora Komi, Location: Charlotte, N.C.

Asked on: Monday, September 8, 2025 at 2:59 pm EDT
Answered on: Monday, September 8, 2025 at 3:05 pm EDT

Question: Hi - I have come across a situation where there seem to be to derating conditions that could apply to a wiringproject. It is for a test lab, and the products in the test lab will be run continuously (continuous use) and also atambient temperatures as high as 140 degrees F. So, in calculating the wire size, do I derate for both the ambienttemperature and continuous duty, or just one condition? And how is the derate calculation performed if bothconditions need to be accounted for? Thanks for the help, I have never run across this before, and haven't foundan answer that I trust online. (oh, and the minimum circuit ampacity of the unit is 500 amps, if that makes any difference.)

Okay, this is a situation where you definitely need to account for both ambient temperature and continuous duty. You're correct to be cautious and seek clarification because improper derating can lead to overheating, insulation breakdown, and even fires.Here's a breakdown of how to handle this situation, incorporating the fact that you're dealing with a large 500A load

1. Understanding the Requirements
Continuous Duty

The NEC (National Electrical Code) defines a continuous load as one where the maximum current is expected to continue for 3 hours or more. For continuous loads, you are required to size the conductors and overload protection to 125% of the continuous load. (NEC 210.19(A)(1) and 215.3).


Ambient Temperature

The insulation rating of wires is based on a specific ambient temperature (typically 30°C or 86°F). When the ambient temperature exceeds this, the wire's current-carrying capacity decreases. You must consult the ampacity correction factors in the NEC (specifically Table 310.15(B)(2)(a), formerly 310.16).

2. The General Process (Step-by-Step)


Let's break down the calculation process into manageable steps: Step 1: Calculate the Adjusted Minimum Ampacity for Continuous Load

Your load is 500 Amps (continuous). Multiply the load by 125%: 500 Amps 1.25 = 625 Amps. This is the minimum ampacity your conductor must have BEFORE applying any temperature derating.



Step 2: Determine the Appropriate Wire Type and Insulation Rating

This is CRITICAL. Given the high ambient temperature (140°F or approximately 60°C), you must select a wire insulation type rated for at least 90°C (194°F). Common examples include THHN/THWN-2, XHHW-2, or RHW-2. Do NOT use wire types with lower temperature ratings. Using lower temperature rated wires, even with derating, is generally not permitted. Consult NEC Table 310.15(B)(16) (formerly 310.16) to find the base ampacity of the conductor you are considering at its rated temperature (usually 90°C).

Step 3: Determine the Temperature Correction Factor

Look up the temperature correction factor in NEC Table 310.15(B)(2)(a) that corresponds to your chosen wire type (e.g., 90°C) and the actual ambient temperature (140°F or 60°C). The table will give you a decimal value (e.g., 0.82).

Step 4: Calculate the Derated Ampacity

Multiply the base ampacity of the conductor (from NEC Table 310.15(B)(16)) by the temperature correction factor (from NEC Table 310.15(B)(2)(a)). `Derated Ampacity = Base Ampacity Correction Factor`

Step 5: Select the Correct Conductor Size

The derated ampacity (from Step 4) must be equal to or greater than the adjusted minimum ampacity for the continuous load (from Step 1, which was 625 amps in your example). If the derated ampacity is less than the required 625 Amps, you must choose a larger conductor and repeat Steps 2-4 until you find a conductor that meets the requirement.

Example (Hypothetical)

Let's say you're considering using XHHW-2 copper conductors.1.

Continuous Load Adjustment

625 Amps (as calculated above).2.

Choose Wire Type

XHHW-2 (rated 90°C). Let's assume that a 750 kcmil XHHW-2 copper conductor has a base ampacity of 665 Amps at 90°C (you must verify this in NEC Table 310.15(B)(16)).
3.


Temperature Correction

For XHHW-2 (90°C) at 60°C (140°F), the correction factor from NEC Table 310.15(B)(2)(a) is, let's say, 0.82 (again, verify this value in the actual table).4.

Derated Ampacity

665 Amps 0.82 = 545.3 Amps.
5.


Conductor Selection

545.3 Amps is
less than the required 625 Amps. Therefore, 750 kcmil XHHW-2 is not sufficient. You would need to move up to a larger conductor size and repeat the calculation. You might need to use multiple conductors in parallel, which is perfectly acceptable and common for large loads.

Important Considerations and Recommendations



NEC is the Authority

Always consult the latest edition of the NEC. Code requirements change, and it is your responsibility to comply.

Enclosure Temperature

Consider the temperature inside enclosures (junction boxes, panels, etc.). It may be higher than the general ambient temperature, requiring further derating.


Number of Conductors in a Raceway/Cable

If you have more than three current-carrying conductors in a raceway or cable, you must also apply ampacity adjustment factors from NEC Table 310.15(B)(3)(a). This is in addition to the temperature correction. This is especially relevant if you are using multiple conductors in parallel.

Voltage Drop

Don't forget to calculate voltage drop. Longer runs will require larger conductors to maintain acceptable voltage at the load. High currents make voltage drop a bigger concern.


Overcurrent Protection

Ensure your overcurrent protection (circuit breaker or fuses) is sized appropriately after derating the conductors, and that it protects the conductors per NEC 240.4.

Professional Consultation

Given the high current and challenging environmental conditions, I
strongly recommend consulting with a qualified electrical engineer. They can perform a detailed load calculation, select the appropriate wiring methods, and ensure compliance with all applicable codes and standards. This is not a DIY project due to the potential safety risks. An engineer can also advise on things like appropriate raceway types, grounding, and bonding.

Aluminum vs. Copper

Consider using aluminum conductors. They are typically less expensive for large sizes. However, you need to account for the slightly lower ampacity of aluminum compared to copper for the same size. Make sure all terminations are rated for use with aluminum conductors (AL-CU rated).

Parallel Conductors

For very large loads like 500 Amps, it's common to use multiple conductors in parallel. This distributes the current, making it easier to manage heat. If you use parallel conductors, they MUST be the same length, conductor material, circular mil area, insulation type, be terminated in the same manner, and have the same physical characteristics. See NEC 310.10(H)


Marking

Clearly mark all conductors and equipment with the adjusted ampacity rating after derating.

In summary, you absolutely need to account for both the continuous load and the high ambient temperature. The process involves adjusting the minimum ampacity for the continuous load, selecting a high-temperature-rated conductor, applying the appropriate temperature correction factor, and ensuring that the derated ampacity meets or exceeds the adjusted minimum ampacity. Do not hesitate to seek professional help for this type of installation. Flag for review

Previous Question Next Question