Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Sealing exterior conduit fittings

User: SceneryDriver, Location: NJ

Asked on: Monday, September 8, 2025 at 3:39 pm EDT
Answered on: Monday, September 8, 2025 at 3:39 pm EDT

Question: The raintight fitting debate has been done to death, and we all agree that the rubber washer is useless.That said, what do folks do when entering the top of an enclosure through a hub, for instance?I had to enter a enclosure through the top with a 2" EMT conduit, and the enclosure came with a 2.5" KO and Myers hub (shop screwed up on the punch size). I had to use a threaded reducing bushing to adapt the Myers hub down to the needed 2" EMT fitting. I ended up using read Loctite 603 retaining compound (thicker and more gap filling than threadlocker) and making up the whole assembly wrench tight before the Loctite set. It worked well, and seems to keep the rain out of the threads.I was told as an apprentice that Loctite is an insulator, but my meter begs to differ. No measurable resistance across the threads after assembly. That makes sense, as the Loctite should fill the gaps in the threads and not interfere with the metal-to-metal contact at the thread faces.I know exterior conduits are considered wet locations, but it still seemed prudent to keep water entry out of the top of the enclosure.Thoughts?SceneryDriver

You've described a pretty common situation and a well-reasoned solution. Here's a breakdown of my thoughts and what others might do

Your Solution is Solid (with Caveats):
Loctite 603

Using Loctite 603 (or a similar retaining compound) is a smart approach. It addresses the inherent leak potential in threaded connections, especially with a reducing bushing. The thicker viscosity is key for filling gaps.


Tight Assembly

Assembling everything tightly before the Loctite cures is crucial for proper sealing and electrical continuity.

Electrical Continuity

Your meter check is important. While Loctite
is a dielectric material in bulk, the thin layer between engaged threads gets displaced under pressure, allowing for reliable metal-to-metal contact.

Code Compliance

Threaded joints require five full threads engaged. I'd ensure there's five full threads engaged in both the bushing and the hub.

Alternative Approaches



O-Ring Hubs/Fittings

Some hubs are specifically designed for wet locations and have an integrated O-ring seal. These are a good alternative if available in the right size and configuration.


Thread Sealant/Paste

Pipe dope specifically rated for electrical use is another option. It's less viscous than a retaining compound, but fills the thread voids.

Silicone Sealant (with caution)

Silicone can be used as a sealant around the
outside of the hub after the connections are mechanically tight. It's crucial to NOT get silicone between the threads, as it will insulate and impede electrical continuity. RTV silicone can be corrosive to copper and other metals. I wouldn't use it in this application.

Replacing the Hub

The "ideal" solution would be to replace the hub with the correct 2" size. This eliminates the need for the reducing bushing entirely and removes one potential point of failure. Of course, this can be time-consuming and costly, especially if the enclosure is already installed.

NPT vs. NPS

Ensure that the reducing bushing threads mate up correctly with both the EMT fitting and the hub's threads. Mismatched threads can leak like a sieve.


Plugs and Gaskets

Some enclosures have provisions for using NPT plugs with gaskets to block off unused conduit entry points.

Key Considerations



UL Listing

Any product used for sealing needs to be UL-listed for the intended application (especially in industrial settings). If using thread sealant, ensure it's specifically rated for electrical use.


Maintenance

While your Loctite solution is probably quite permanent, consider future maintenance. If the conduit needs to be removed later, it might be very difficult with the adhesive.

Environment

Extreme temperature swings can cause expansion and contraction that can stress seals over time.


Enclosure Rating

Make sure your chosen solution maintains the enclosure's NEMA rating for weather-tightness.

Electrolytic Corrosion

Keep dissimilar metals separated with paint, tape or appropriate washers/sleeves.

Why the Rubber Washer is Useless (Recap)

The infamous rubber washer is generally considered useless because:
It doesn't compress effectively to seal around the threads of the fitting. It tends to slide out of position during tightening. It offers no protection against water wicking up through the conduit itself.

In summary:


Your approach with Loctite 603 is a reasonable and potentially effective solution for sealing the threads and maintaining electrical continuity, provided that the materials are compatible and the assembly is done carefully. The O-ring hub solution is the cleanest, most professional way to go if its available. For long-term reliability, consider the alternatives and the specific environmental conditions. In most cases, keeping water out of the enclosure is worth the effort! Flag for review

Previous Question Next Question