Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Shared neutral between normal power and generator power

User: Brownetown, Location: Va

Asked on: Monday, September 8, 2025 at 11:29 pm EDT
Answered on: Monday, September 8, 2025 at 11:30 pm EDT

Question: I have a lighting upgrade of an older high school in process. Fixture for fixture. I came across that in one section of the building they pulled 12/3 one being generator power. One being normal SL power and then a shared neutral between the two. What are your thoughts on that. I know the neutral is obviously the same threw out the 480v/277 service coming in. But tech ally it’s freed from a different source.

Okay, this is a situation that needs careful evaluation. Here's a breakdown of the potential issues and considerations

The Potential Problems with Shared Neutrals for Different Power Sources (Normal and Generator):
Overloading the Neutral

The primary concern is overloading the neutral conductor. The neutral is sized to carry the imbalanced current from the phase conductors. If you have both normal power and generator power contributing to the load on a
shared neutral, it's possible (and even likely under some conditions) to exceed the neutral's ampacity.

How it happens

If the loads on the normal power and generator power are unbalanced in the same direction (e.g., both have more load on phase A than phase B and C), the neutral current can be significantly higher than what you'd expect from a single circuit. This is especially true if the loads are non-linear (e.g., LED lighting with high harmonic content).

Harmonic Currents

Modern lighting (especially LED) can generate significant harmonic currents. These harmonics are additive in the neutral conductor and can easily overload it, even if the fundamental (60 Hz) current seems within limits. Using different sources can exacerbate the problem if they have different harmonic profiles.


Neutral Potential Rise

Overloading the neutral can cause a voltage drop across the neutral conductor, leading to a voltage rise relative to ground at the load. This can cause equipment malfunction, flickering lights, and potentially damage sensitive electronics.

Generator Protection Issues

Generators rely on a solid neutral connection for proper fault detection and overcurrent protection. A shared neutral with another power source can interfere with the generator's ability to accurately sense faults and trip the breaker.


Backfeed and Interconnection Issues

A shared neutral can create a path for unintentional backfeeding of power between the normal power and the generator, even if the generator is not intended to be connected in parallel with the utility. This is a severe safety hazard and could damage equipment or injure personnel.

Code Violations

While the shared neutral itself might not inherently violate the NEC, the
resulting overloading, backfeeding, and potential for unsafe operation would likely violate numerous sections of the code, including those related to conductor ampacity, overcurrent protection, and safe equipment operation.

Why it Might Have Been Done (Historically, and Why it's Usually Wrong)



Cost Savings

Running a single neutral wire is cheaper than running two. However, this is a false economy when considering the potential risks and consequences.

Misunderstanding of the Neutral's Role

Some electricians might have incorrectly assumed that because the neutral is ultimately tied to the same grounding electrode conductor (GEC) at the service entrance, it's "okay" to share it. This is a dangerous simplification.


Older Practices

Before the widespread use of non-linear loads (like modern electronics and LED lighting), the risks of shared neutrals were less pronounced.

What You MUST Do


Do Not Continue with the Upgrade Without Correcting the Wiring

Upgrading the lighting without addressing this wiring issue is irresponsible and potentially dangerous.2.

Consult a Qualified Electrical Engineer or Senior Electrician

This is NOT a DIY situation. You need someone with the expertise to:

Thoroughly Inspect and Document the Existing Wiring

Map out
exactly how the circuits are wired, where the neutrals are shared, and what the loads are. Take detailed measurements of voltage, current (including neutral current), and harmonic distortion under both normal power and generator power.

Calculate Neutral Loading

Based on the existing and proposed loads, calculate the current on the shared neutral under various scenarios (normal power only, generator power only, both sources potentially contributing). Consider the impact of harmonic currents.

Determine the Appropriate Course of Action

This will likely involve:


Separating the Neutrals

The most likely and safest solution is to run dedicated neutral conductors for the normal power and generator power circuits. This eliminates the risk of overloading and backfeeding. This might involve pulling new conductors or repurposing existing ones.

Upgrading the Shared Neutral

If separating the neutrals is impossible (e.g., due to conduit fill limitations), the
absolute minimum is to upgrade the shared neutral conductor to a larger size that can safely handle the calculated load, including harmonic currents. However, this still doesn't address the potential for backfeeding or generator protection issues.

Consider a Dedicated Neutral for Each Fixture/Circuit

To further reduce the load on any one neutral and to accommodate the harmonics caused by the LEDs, consider using a dedicated neutral for each fixture or each circuit.*

Consider a Neutral Current Filter

If separating the neutrals is not feasible (due to conduit fill limitations), a neutral current filter on the shared neutral can help to reduce the current and harmonics present.3.

Adhere to the National Electrical Code (NEC) and Local Codes

Ensure that all work is performed in accordance with the latest edition of the NEC and any applicable local codes and regulations. Pay particular attention to Article 300 (Wiring Methods), Article 310 (Conductors for General Wiring), Article 220 (Branch-Circuit, Feeder, and Service Calculations), and Article 700 (Emergency Systems).4.

Consider the Generator's Requirements

Consult the generator manufacturer's documentation to ensure that the wiring configuration is compatible with the generator's protection and grounding requirements.5.

Verify with the Authority Having Jurisdiction (AHJ)

Discuss the proposed solution with the local electrical inspector to ensure that it meets their requirements.6.

Document Everything

Keep detailed records of the existing wiring, the calculations, the proposed solution, and the actual work performed.

In summary, shared neutrals between normal and generator power are almost never a good idea, especially with modern electronic lighting. You need to address this issue before proceeding with the lighting upgrade. Prioritize safety and compliance with the NEC and local codes.
Flag for review

Previous Question Next Question