User: hhsting, Location: Glen bunie, md, us
Asked on: Tuesday, September 9, 2025 at 8:33 am EDT
Answered on: Tuesday, September 9, 2025 at 8:33 am EDT
Question: For GFCI for Open Fryers and Dishwashers, the engineer is using SB5000 series Little fuse Shock Block Device. See the link below for that device. Would this comply with NEC 2017 as gfci protection or GFCI would need to be at breaker or at receptacle level?
Okay, let's break down the GFCI requirements for open fryers and dishwashers according to the NEC 2017 and how the Littelfuse SB5000 Shock Block device fits in.
NEC 2017 Requirements (Relevant Sections)
The key section that dictates GFCI protection for these types of equipment is typically NEC 2017 Article 422: Appliances. Within Article 422, pay close attention to: 422.5(A) General
Requires GFCI protection for specific appliances in dwelling units and commercial locations, as specified in other sections of 422.
422.5(B) Kitchens
Specific requirements for kitchen appliances. While the general kitchen GFCI rules might not explicitly mention open fryers, the location (kitchen) often triggers requirements. Dishwashers in dwelling units nearly always require GFCI protection.
422.5(C) Boathouses
Specific requirements for boathouses.
422.5(D) Outdoors
Specific requirements for outdoors.
422.5(E) Other Locations
This is a catch-all. It states that GFCI protection shall be provided for personnel protection for cord-and-plug-connected appliances installed in the locations specified in 210.8.
210.8(B) Other Than Dwelling Units
This section is VERY important for commercial kitchens. It requires GFCI protection for receptacles serving: Kitchens Bathrooms Rooftops Outdoors
Understanding the Littelfuse SB5000 Shock Block Device
The Littelfuse SB5000 Shock Block is a Personnel Protection Device (PPD), not a GFCI in the traditional sense. While it provides shock protection, it functions slightly differently. It's designed to be installed within the equipment or as part of the cord, and it detects ground faults and interrupts the circuit.
Does the SB5000 Comply with NEC 2017 as GFCI Protection?The short answer is: It DEPENDS on the specific application, the AHJ interpretation, and the precise wording of the NEC codes being enforced.
Here's a breakdown of why and how it can potentially be used, and what to consider: Acceptable Application
The SB5000 Shock Block is designed to provide shock protection at the appliance itself. It's a specialized device.
If the appliance is cord-and-plug-connected
The equipment would be required to be GFCI Protected.
Installation requirements
Check with the local inspector and equipment manufacturer.
Important Considerations and Best Practices
Consult with the Authority Having Jurisdiction (AHJ)
This is crucial. The local electrical inspector has the final say. Present the SB5000 specifications and application to them and ask if they accept it as a form of GFCI protection in lieu of or in addition to receptacle or breaker GFCI.2.
UL Listing
Ensure the SB5000 is UL-listed or has another nationally recognized testing laboratory (NRTL) listing that specifically covers its use for personnel protection in the intended application (open fryer or dishwasher). This is a must.3.
Manufacturer's Instructions
Follow the Littelfuse installation instructions precisely. Any deviation could void the UL listing and create a safety hazard.4.
Maintenance
Make sure maintenance personnel are trained on how to test and reset the Shock Block device. Document the maintenance procedures.5.
Documentation
Keep all documentation (SB5000 specifications, UL listing information, installation instructions, AHJ approval documentation) readily available.6.
Consider Redundancy
In some cases, the AHJ might require both a GFCI breaker/receptacle AND the SB5000 Shock Block for enhanced safety, especially in high-risk environments like commercial kitchens.
In summary: The Littelfuse SB5000 Shock Block can potentially be used as a means of personnel shock protection for open fryers and dishwashers, but it's NOT a direct replacement for traditional GFCI protection at the breaker or receptacle without AHJ approval. You MUST consult with the local electrical inspector (AHJ) to confirm its acceptability for the specific application and local code interpretations. Ensure it's UL-listed, installed correctly, and properly maintained.* Be prepared to potentially use it in conjunction with breaker/receptacle GFCI protection for enhanced safety. Flag for review