Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Motor Calculation

User: Seven-Delta-FortyOne, Location: Humboldt

Asked on: Tuesday, September 9, 2025 at 12:02 pm EDT
Answered on: Tuesday, September 9, 2025 at 12:04 pm EDT

Question: Got specs for some equipment that I have to supply wiring and disconnect for.Manufacturer sent us the following: "Booster pump 3HP 230V/3 Phase @ 9.6 Amps (230V 1 Phase @ 34 Amps)" and Backwash pump 5HP 230V/3 Phase @ 15.2A ( 230V 1 Phase @ 54A)"I believe those figures to be wrong. I've calc'd it many times and I have 17A @ 1 Phase for the 3HP and 28A @230V for the 5HP. I have assumed a PF of .80 on my calcs.Have I done my calculations wrong?

Let's break down the calculations and see where the discrepancies might be. I suspect the manufacturer might be more accurate than you think, and here's why

Your Calculations (Let's Verify):
Formula

The basic formula to calculate Amps from HP, Voltage, and Power Factor is:
I = (HP 746) / (Voltage Power Factor Efficiency)Let's assume a reasonable efficiency of 85% (0.85) for induction motors. This is a crucial assumption. A lower efficiency significantly increases current draw.

Booster Pump (3HP, 230V, 1-Phase, PF=0.8, Efficiency=0.85)

I = (3 746) / (230 0.8 0.85) I = 2238 / 156.4 I ≈ 14.3 A

Backwash Pump (5HP, 230V, 1-Phase, PF=0.8, Efficiency=0.85)

I = (5 746) / (230 0.8 0.85) I = 3730 / 156.4 I ≈ 23.9 A

Booster Pump (3HP, 230V, 3-Phase, PF=0.8, Efficiency=0.85)

I = (3 746) / (230 0.8 0.85 1.732) I = 2238 / 270.7 I ≈ 8.3 A

Backwash Pump (5HP, 230V, 3-Phase, PF=0.8, Efficiency=0.85)

I = (5 746) / (230 0.8 0.85 1.732) I = 3730 / 270.7 I ≈ 13.8 AYour figures for 1 phase are lower than what I calculated. I suspect you have made a mistake in your calculation. Regardless, both our numbers are lower than the manufacturer.

Why the Manufacturer Might Be Correct (or Closer to Reality)


Motor Efficiency

We
assumed an 85% efficiency. Smaller motors (especially those in pumps) can often have significantly lower efficiencies. If the actual efficiency is, say, 65% or 70%, the current draw goes up dramatically.2.

Service Factor

Motors often have a "service factor" (SF). This is a multiplier that allows the motor to handle slightly more load than its rated HP
for short periods. While you don't typically design for continuous operation at the service factor, the motor will draw more current if it's operating at or near its SF. A service factor of 1.15, for example, means the motor can handle 15% more load for a limited time, resulting in higher current.
3.


Pump Load Profile

The actual load on the pump can vary significantly based on the system's pressure, flow rate, and other hydraulic characteristics. If the pumps are operating near their maximum head pressure or flow rate, they will draw more current.4.

Locked Rotor Amps (LRA)

The manufacturer might be giving you the LRA or a value close to it. LRA is the current a motor draws when it's first starting. It's significantly higher (5-7 times the running current) but only lasts for a very short time (seconds). However, LRA is usually specified separately, so this is less likely.5.

Manufacturing Variation/Conservative Rating

Manufacturers sometimes provide more conservative ratings to account for manufacturing variations, worst-case operating conditions, or to provide a safety margin.6.

Include Control Panel Loads

The manufacturer's values
could potentially include the current draw of any control panel components (relays, timers, etc.) associated with the pump. This is less likely but possible.7.

Starting

The motor's load might require a soft start due to the friction of starting under a full load. A soft start will increase your running amps considerably.

Recommendations


Double-Check Efficiency

Ask the manufacturer for the
actual motor efficiency at the specific operating conditions. This is the most crucial piece of information. Get a motor nameplate photo, if possible. The nameplate will often list the FLA (Full Load Amps) which is the manufacturer's rated current draw.2.

Confirm Service Factor

Verify the motor's service factor.3.

Operating Conditions

Inquire about the expected operating head pressure and flow rate of the pumps. This will give you a better idea of the actual load on the motors.4.

Soft Start

Inquire if you are going to need to use a soft start. If that's the case, you will need to specify a larger wire to compensate for the inrush current.5.

Clarify the Data

Directly ask the manufacturer: "Are these Full Load Amps (FLA) or some other value? Do these figures include any other loads (e.g., control panel)?"6.

Err on the Side of Caution

When in doubt, it's
always* safer to use the manufacturer's data for wire sizing and disconnect selection. Oversizing is preferable to undersizing.7.

Local Codes

Always adhere to your local electrical codes. They may have specific requirements for motor circuit sizing.8.

Consult an Electrical Engineer

If the discrepancies are significant and you're unsure, consult with a qualified electrical engineer.

In conclusion, it's very likely that the manufacturer's numbers are closer to the real-world operating current of the pumps, especially when considering factors like efficiency and pump load. Get clarification from the manufacturer on the motor specifications.
Flag for review

Previous Question Next Question