Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Entering Equipment

User: Alwayslearningelec, Location: NJ

Asked on: Wednesday, September 10, 2025 at 7:32 am EDT
Answered on: Wednesday, September 10, 2025 at 7:32 am EDT

Question: Howe would you enter an existing piece of equipment on grade if running underground conduit to it? Guess you could not enter from bottom but would have to come up on side.

You're right, you can't typically enter an existing piece of equipment directly from the bottom if it's sitting on grade. Here's how you'd approach running underground conduit to that equipment and entering it from the side, along with considerations

1. Planning and Considerations:
Equipment Location and Type

What
exactly is the equipment? (e.g., A/C unit, generator, electrical panel, pump motor). This impacts conduit size, wire requirements, and allowable entry points. Also, understand the equipment's NEMA rating (ingress protection) to ensure your entry point maintains that rating.

Code Compliance

NEC (National Electrical Code) rules govern underground wiring, conduit fill, bonding/grounding, and proper terminations. Consult your local codes and regulations. This is critically important.



Clearances

Maintain required clearances around the equipment (for access, maintenance, and safety). Check local codes.


Ground Conditions

Understand the soil type, potential for settling, and water table depth. This affects the depth of your trench and the type of conduit you use.

Existing Utilities

Call before you dig! Locate and mark any existing underground utilities (gas, water, phone, power) to prevent damage.


Entry Point

Examine the equipment. Is there a designated knockout, hub, or entry point on the side? If not, can you safely and legally create one? (e.g., drill and tap a new hole, or use a suitable adapter).

Do not compromise the structural integrity of the equipment.

Environmental Considerations

Consider the climate and any potential for corrosion. Use appropriate conduit materials and fittings.


Conduit Type

Common choices are:

Rigid Metal Conduit (RMC)

Durable, provides good physical protection, but can be more expensive and harder to work with. Requires grounding bushings and bonding.


Intermediate Metal Conduit (IMC)

Lighter than RMC, still strong. Requires grounding bushings and bonding.

Rigid PVC Conduit

Corrosion-resistant, lightweight, and easy to work with. Requires a grounding conductor to be pulled inside the conduit.


Electrical Metallic Tubing (EMT)

Not suitable for direct burial.

2. The Process


Trenching

Dig a trench from the equipment location back to the source of power (or where the conduit run will start). The trench depth must comply with local codes. Generally, PVC direct burial needs to be at least 18 inches deep, and rigid metal needs to be at least 6 inches deep. Check your local codes as these can vary. Maintain a consistent slope in the trench to prevent water accumulation inside the conduit. Ensure the bottom of the trench is smooth and free of sharp rocks or debris that could damage the conduit. Consider using a sand bedding.2.

Conduit Installation

Assemble the conduit run in the trench, using appropriate fittings (couplings, elbows, etc.). Use PVC glue designed for electrical conduit (if using PVC). If using metal conduit, ensure all connections are tight and use appropriate grounding bushings and bonding jumpers to maintain electrical continuity. Consider using sweeps (large radius elbows) to minimize pulling tension when installing the wires. If the run is long or has many bends, consider installing pull boxes along the way to make wire pulling easier.3.

Entering the Equipment



Side Entry

This is the most common approach.


Existing Knockout/Hub

If the equipment has a knockout or hub on the side, use the appropriate size connector to attach the conduit.

Creating a New Entry Point

This is where you need to be very careful and consult the manufacturer's instructions and a qualified electrician.

Identify a suitable location on the side of the enclosure (avoiding internal components). Use a hole saw or knockout punch to create an opening of the correct size for the connector. Use a connector that is approved for the type of enclosure and the type of conduit you are using. Ensure the connector is properly sealed to maintain the enclosure's NEMA rating. Seal Properly

Use weatherproof connectors and sealant (if required) to prevent moisture from entering the equipment. Maintain the NEMA rating.


Secure the Conduit

Support the conduit as it enters the equipment to prevent strain on the connection. Use conduit straps or clamps.4.

Wire Pulling

After the conduit is in place, pull the wires through the conduit. Use a wire pulling lubricant to reduce friction. Ensure the wires are the correct gauge and type for the load. Leave sufficient wire length inside the equipment for making connections.5.

Terminations

Terminate the wires inside the equipment according to the equipment manufacturer's instructions and NEC guidelines. Ensure all connections are tight and properly insulated. Pay close attention to grounding and bonding requirements.6.

Backfilling

Before backfilling, inspect the entire conduit run and connections to ensure everything is secure and properly installed. Backfill the trench with soil, compacting it in layers to prevent settling.

Example Scenario: Running Conduit to an Outdoor Air Conditioner Unit
1. Trench

Dig a trench from the A/C unit to the house (where the circuit breaker is located). Trench depth to code requirements.2.

Conduit

Use rigid PVC conduit (because it's corrosion-resistant and relatively easy to work with).3.

Side Entry

The A/C unit has a knockout on the side. Knock out the appropriate-sized hole. Use a PVC male adapter to connect the conduit to the A/C unit. Use PVC cement. Ensure the connection is watertight (use sealant if necessary).4.

Wire Pulling

Pull the correct gauge wires (e.g., THHN) through the conduit. Also pull a grounding conductor.5.

Terminations

Connect the wires to the A/C unit's disconnect switch or terminal block. Connect the grounding conductor to the grounding terminal.6.

Backfill

Backfill the trench, compacting the soil.

Important Considerations and Cautions



Electrical Safety

Always de-energize the circuit before working on electrical wiring. Verify the circuit is off with a voltage tester.

Qualified Electrician

If you're not comfortable working with electricity, hire a qualified electrician. Working with electricity can be dangerous, and mistakes can be costly or even fatal. Many jurisdictions
require a licensed electrician for electrical work.

Permits

Check with your local building department to see if a permit is required for the electrical work.

Manufacturer's Instructions

Always follow the equipment manufacturer's instructions for installation and wiring.


Grounding and Bonding:
Proper grounding and bonding are essential for safety. Consult the NEC for specific requirements.By carefully planning and executing the steps outlined above, you can safely and effectively run underground conduit to an existing piece of equipment on grade. Remember to prioritize safety and consult with a qualified electrician if you have any doubts. Flag for review

Previous Question Next Question