Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Covering hole in plastic box

User: Will Wire, Location: California: NEC 2020

Asked on: Thursday, September 11, 2025 at 10:35 am EDT
Answered on: Thursday, September 11, 2025 at 10:35 am EDT

Question: Other than removing the box and replacing it, is there a code compliant method for covering a hole in a box when a Romax wire has been removed during a remodel and the box supplies a receptacle in another room and will be remaining. Thanks.

You're right to be concerned about code compliance. Leaving an open hole in an electrical box is a definite safety hazard and violates several electrical codes. Here's a breakdown of why it's a problem and code-compliant solutions without replacing the box

Why an Open Hole is a Problem and Code Violations:
Fire Hazard

The box is designed to contain sparks or arcing that could occur within the box. An open hole allows these sparks to escape and potentially ignite surrounding materials.


Shock Hazard

Live conductors are exposed, creating a dangerous shock hazard. Children or animals could easily come into contact with these.

Environmental Protection

Boxes are designed to prevent dust, moisture, and other contaminants from entering and damaging connections.


NEC (National Electrical Code) Violation

Specific violations depend on your local jurisdiction's adoption of the NEC, but generally, leaving openings in electrical boxes violates requirements for:

110.12(A) Neatly and Workmanlike Manner

Openings detract from a neat and workmanlike installation.


314.17(B) Protection of Conductors Entering Boxes, Conduit Bodies, or Fittings

The box must protect the wires.

314.21 Repair of Walls, Ceilings, or Other Surfaces

Any repair should leave the installation neat and workmanlike and maintain any fire rating.


314.40(A) Fittings and Connectors

Fittings and connectors must be properly used with boxes.

Code-Compliant Solutions (Without Replacing the Box)

The key is to effectively close the hole in a manner that restores the integrity and safety of the box. Here are the best options:1.

Using a Listed Hole Plug/Knockout Seal



What it is

These are specifically designed, often circular, plastic or metal plugs that snap or screw into knockout holes in electrical boxes. They are
listed (UL, ETL, etc.) for this purpose, which means they've been tested and certified to meet safety standards.

How to Use

Measure the diameter of the hole. Purchase a knockout seal of the correct size. Snap or screw the seal into the hole.

Why it's good

This is generally the
best and most code-compliant method because it restores the box to its original intended state. It's inexpensive and readily available at any hardware store.2.

Using a Conduit Fitting and a Blank Cover



What it is

This method involves using a short section of conduit (e.g., EMT or PVC) and an appropriate fitting to attach it to the box. Then, a blank cover plate is installed on the other end of the conduit section.

How to Use

1. Select the appropriate conduit fitting (e.g., a knockout connector or a set-screw connector) that matches the size of the hole in the box and the type of conduit you'll be using.
2. Attach the fitting to the box.3. Cut a short piece of conduit (e.g., 1-2 inches).
4. Attach a conduit body with a blank cover on the other end of the short conduit section.


Why it's good

This provides a physical barrier that is more robust than a knockout seal alone. It is a good option if the hole is larger or an irregular shape and you can't get a knockout seal to fit properly.

Important Considerations



Material Compatibility

If the box is metal, using a metal knockout seal or conduit fitting is generally preferred to maintain grounding continuity. Plastic knockout seals are fine in plastic boxes.


Secure Installation

Make sure the chosen method provides a tight, secure seal that won't easily dislodge.

Accessibility

Once sealed, the hole should not be easily reopened.


Local Codes

Always consult your local electrical codes and inspectors. Some jurisdictions may have specific requirements or preferences. It's always a good idea to ask your local electrical inspector if you have any questions about compliance.

What NOT to Do



Electrical Tape

Wrapping the hole with electrical tape is
not an acceptable solution. It's not durable, doesn't provide adequate protection, and is not code-compliant.

Caulk or Sealant

While sealant might seem like a quick fix, it's generally not a code-compliant solution unless the sealant is specifically listed for use in electrical boxes. It's also not easily removable if future work is needed.*

Leaving it Open

As discussed, this is a major safety hazard and code violation.

In summary, using a listed knockout seal is almost always the best and easiest solution. If that's not possible, a short section of conduit and a blank cover plate can also be used. Always ensure a secure, code-compliant repair for safety and peace of mind.
Flag for review

Previous Question Next Question