Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Hot Tub Disconnect and Equipotential Bonding?

User: raykit65, Location: Franklin, TN

Asked on: Friday, September 12, 2025 at 2:26 pm EDT
Answered on: Friday, September 12, 2025 at 2:29 pm EDT

Question: Here is my scenario....I have a new free standing hot tub that was installed during a deck renovation that replaced an existing hot tub.The hot tub is installed on slab but with an elevated deck built around it so just the hot tub edge sits above the deck.The hot tub is under a roof and inside room with solid wood walls about 30" tall and screen above.I am replacing some conduit and wire (previous 'electrician' sleeved 6/3 under the deck along with other violations)Here are my concerns as I don't do a lot of hot tubs....The existing disconnect is less than 5' but on the other side of the 30" wall. It is technically out of sight when you are inside the tub but clearly visible as you are walking in and out. Is this location fine or do I need to relocate it onto the house where it is 5'+ away and visible through the screen door while in the tub?The tub sits above the 28" rule for equipotential bonding however the deck changes that. Do I need to install the bonding wires around the tub?**See attached pic and rough sketch**

Okay, let's break down your hot tub electrical concerns and address them based on the information you've provided and generally accepted NEC guidelines. Disclaimer

I am an AI and cannot provide code-compliant electrical advice. Consult with a licensed electrician for a final, code-compliant installation.

1. Disconnect Location


This is a common point of confusion. Here's the key considerations regarding the disconnect: Visibility

The NEC requires the disconnect switch to be readily accessible and within sight of the hot tub's equipment (pumps, heater, etc.). This means the equipment, not just the tub water, needs to be visible.


Distance

The disconnect must be located at least 5 feet (1.5 m) horizontally from the inside walls of the hot tub.

Accessibility

The disconnect must be readily accessible.

Your Specific Situation



Visibility Issue

While you can see the disconnect as you enter/exit, the fact that it's behind a 30" wall and not directly visible from the hot tub itself is problematic. The point of being able to see it is to quickly shut off power in an emergency from within the tub. If you have to get out of the tub, walk around a wall, to shut off the breaker, that fails the purpose.

Distance issue

This part is likely to be up for interpretation by your inspector. Is the distance less than 5ft from the inside edge of the tub to the disconnect? If so, this is a code violation.

Recommendation

Relocate the disconnect. Mounting it on the house wall 5' or more from the inside edge of the tub will likely be the better option. Being visible through the screen door satisfies the "within sight" requirement, assuming it's a clear view.

2. Equipotential Bonding


This is crucial for safety. Equipotential bonding aims to minimize voltage differences in and around the hot tub to prevent electrical shock hazards.

Key Considerations



28" Rule

The 28" rule applies to surfaces within 28" horizontally of the inside walls of the tub and that are likely to become wet. All metal components within this area must be bonded.

Deck as a Conductive Surface

Your deck is the critical factor. Because the deck is raised and surrounds the tub, it's considered an "area likely to become wet" and therefore included in the 28" rule.


Bonding Grid/Perimeter Bond

If the deck is conductive or has metal within 28" of the inside wall of the tub, you must install an equipotential bonding grid or perimeter bond around the hot tub. This involves running a solid copper conductor (usually #8 AWG) and bonding it to any metal parts that could become energized, such as metal deck supports, metal railings, metal light fixtures, etc.

Your Situation



Yes, you likely need bonding.
Your deck significantly impacts the 28" rule. You will likely need to run a #8 solid copper conductor around the perimeter of the tub/deck area and bond it to all metal objects within reach. This includes metal parts of the hot tub itself (following the manufacturer's instructions, usually a bonding lug on the control pack).

Important Notes on Bonding



Continuous Conductor

The bonding conductor must be continuous (no splices).

Proper Connections

Use approved bonding connectors (listed for direct burial, if necessary) to make secure connections to the metal components.


Professional Installation

Given the critical nature of equipotential bonding, it's highly recommended to have a qualified electrician perform this work.

Summary and Recommendations
1. Disconnect

Relocate the disconnect to the house wall at least 5 feet away from the inside edge of the hot tub and visible from the tub area.2.

Equipotential Bonding

Install a perimeter bond (typically #8 solid copper) around the perimeter of the hot tub/deck area, bonding it to all metal components within 28" of the inside walls of the tub.3.

Consult a Licensed Electrician

This information is for guidance only. You absolutely must have a licensed electrician inspect your installation, ensure compliance with all applicable codes (NEC and local), and perform the necessary wiring and bonding. They can properly assess your specific site conditions and provide the most accurate and safe solution.

Safety is paramount with hot tub electrical installations. Don't take shortcuts or rely on DIY advice when it comes to electricity and water.
Flag for review

Previous Question Next Question