User: nizak
Asked on: Sunday, September 14, 2025 at 10:45 am EDT
Answered on: Sunday, September 14, 2025 at 10:47 am EDT
Question: Looking to get power to a vehicle storage lift in an attached garage.The spec sheet says “115V 20 amp 1Ph” for the power requirements.from the panel with a new circuit involves running approximately 115’ through 3 sections of finished basement. 2 areas drop ceiling, one 12’ space drywall ceiling then into the garage and 20’ of 700 Wiremold.I have an existing 120 V receptacle within 3’ of where the power pack plugs into.That circuit currently has around 7 amps of load on it.I do know it’s a 1HP motor but don’t know any other specs. Equipment is not on site but owner would like it ready when the installers come.It operates a small hydraulic pump that turns the gear box.In the past I’ve used Mfgr info stating the need for a dedicated circuit only to find a minimal amp draw once the equipment arrived.Thoughts on how to handle this
Okay, let's break down this situation and consider your options. You're right to be cautious and consider all factors before running a new circuit. Here's a structured approach
1. Understanding the Requirements & Potential Issues:
Dedicated 20A Circuit is Recommended (and Likely Required)
The manufacturer specifying "115V 20 amp 1Ph" strongly suggests a dedicated circuit is required for safe and reliable operation. While it might work on an existing circuit, there are significant risks. The primary reason is a sudden surge that may not trip the breaker immediately and cause damage to other equipment on the same circuit.
Motor Starting Current
1 HP motor (even a small one) can draw a significant surge of current when starting. This inrush current is much higher than the running current. This surge could trip the existing circuit's breaker, even if the running current is low. It can also cause voltage drops that affect other equipment on the same circuit.
Continuous Load
If the lift's motor runs for extended periods during a lift cycle, it's considered a "continuous load" by electrical codes. This means the circuit should only be loaded to 80% of its rated capacity. A 20A circuit can only handle 16A continuously. This further reinforces the need for a dedicated circuit.
Code Compliance
Local electrical codes generally require adherence to manufacturer specifications for equipment. Using an existing, under-sized circuit could violate code and create safety hazards.
Liability
If you wire the lift improperly and it causes damage or injury, you could be liable.
Wire Length and Voltage Drop
The 115-foot run from the panel is significant. Voltage drop can become a problem, especially under load. A voltage drop means that the lift motor won't receive the full 115V it needs. This can cause the motor to run hotter, perform poorly, and shorten its lifespan. You'll need to calculate the correct wire gauge to minimize voltage drop.
2. Gathering More Information (Ideal Scenario)
Before doing anything, try to get more information:
Motor FLA (Full Load Amps)
Find the motor's FLA (Full Load Amps) rating. It is usually on the motor's nameplate. This is the continuous current the motor draws when running under full load.
Motor LRA (Locked Rotor Amps)
If possible, get the motor's LRA (Locked Rotor Amps) rating. This is the inrush current when the motor starts. This is the most important factor to consider in a situation like this.
Contact the Manufacturer
If the spec sheet is vague, call the lift manufacturer. Specifically ask: "Is a dedicated 20A circuit required or merely recommended?" "What is the maximum current draw during a full lifting cycle?" "What is the motor's FLA and LRA?" "Are there any specific wire gauge or breaker type recommendations?"
3. Analyzing the Existing Circuit (If You Insist on Considering It)
Verify the Breaker Size
Confirm the existing receptacle is on a 15A or 20A breaker. Never replace a smaller breaker with a larger one without verifying the wire gauge can handle the increased current.
Check the Wire Gauge
Open the receptacle and check the wire gauge. 14 AWG is typically used for 15A circuits, and 12 AWG for 20A circuits. Never connect a 20A load to a 15A circuit.
Trace the Circuit
Carefully trace the circuit back to the panel to identify everything else that's on it. The 7A you measured is only part of the story. There could be other loads that are only used occasionally.
Calculate Total Potential Load
Add up the amperage of everything on the circuit, including the 7A existing load and the lift's FLA (once you get it). If the total exceeds 80% of the breaker's rating, it's a non-starter.
4. Why the Dedicated Circuit is Almost Always the Right Choice
Even if the lift seems to work on the existing circuit, running a dedicated circuit is almost always the best approach for the following reasons:
Safety
Reduces the risk of overloaded circuits, breaker tripping, and potential fires.
Reliability
Ensures the lift operates reliably without being affected by other loads on the circuit.
Code Compliance
Ensures your work meets electrical code requirements.
Future-Proofing
Provides a dedicated circuit for the lift, preventing future issues if you add more equipment to the garage.
Peace of Mind
You'll know the lift is wired correctly and safely, reducing worry.
5. Running the Dedicated Circuit (Recommended Approach)
If you run a new circuit:
Wire Gauge
Given the 115-foot run, use 12 AWG wire at a minimum. Calculate voltage drop to determine if a larger gauge (10 AWG) is necessary. Use an online voltage drop calculator, inputting the wire length, amperage (FLA of the motor), and voltage. Aim for a voltage drop of less than 3%.
Conduit/Wiring Method
Since you're running through a finished basement, you'll need to use appropriate wiring methods. This typically means running the wire inside conduit (EMT or PVC) or using cable (like NM-B or MC cable) that is properly secured. Check your local electrical codes for specific requirements. For the 700 Wiremold, use the appropriate fittings and wiring method approved for use within Wiremold.
Breaker
Use a 20A single-pole breaker. A standard thermal-magnetic breaker is likely sufficient, but check with the lift manufacturer for specific recommendations.
Receptacle
Install a standard 120V 20A receptacle (NEMA 5-20R).
Grounding
Ensure proper grounding of the circuit and the lift equipment.
Permits & Inspection
Check your local regulations regarding electrical permits and inspections. It's generally a good idea to get a permit and have the work inspected to ensure it's done safely and to code.
6. Important Considerations for Wire Runs
Securing the Wire
In the drop ceiling and drywall ceiling, the wire needs to be properly supported and secured according to code. This often involves using cable ties, straps, or other approved methods to prevent the wire from sagging or becoming damaged.
Penetrations
When passing the wire through walls or ceilings, use appropriate fittings and sleeves to protect the wire from damage.*
Clearances
Maintain proper clearances from other utilities (plumbing, HVAC) and from combustible materials.
In summary: While the idea of using the existing receptacle is tempting for simplicity, it's almost certainly a bad idea. The risk of overloading the circuit, voltage drop, and code violations outweighs any convenience. The best and safest approach is to run a dedicated 20A circuit from the panel, using the correct wire gauge and wiring methods for your specific situation. Consult with a qualified electrician if you are unsure about any aspect of this process. Flag for review