Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Calculating Secondary Inrush Current for Isolation Transformer

User: bellington, Location: Hahira, GA

Asked on: Sunday, September 14, 2025 at 12:05 pm EDT
Answered on: Sunday, September 14, 2025 at 12:06 pm EDT

Question: Good morning to my electrical math wizards,I have a 3-phase 500 kVA isolation transformer 480 delta fed by a EPC 500 kW inverter powered by a 1107 kWH battery, to 480 wye fed to switch gear. There is a 450 kW generator to charge the battery when solar is inadequate. In black start conditions, the generator breaker typically trips, unless I open the battery inverter breaker on the primary side of the transformer, then close the generator switch gear breaker, then close the transformer breaker.The company that installed the equipment keeps discussing the need for a coordination study. But, it is my thoughts that the secondary, wye, side of the transformer may actually have a higher inrush current than the delta primary. I also think that while setting a longer delay on the generator may prevent the generator breaker from tripping, I don't want the generator being exposed to that current.1. Are there reliable calculations that will provide the inrush current and the length of time the generator would be exposed to that current?2. What is the least costly and most effective way of limiting the inrush current on the output side of the generator?

Good morning! This is a complex setup with several interacting components. Let's break down the inrush current issue and potential solutions.

Understanding Inrush Current Transformer Inrush

Transformer inrush current is a very short-duration, high-magnitude current that occurs when a transformer is energized. It's caused by the core's magnetic flux not being in phase with the applied voltage at the moment of energization. The core attempts to saturate, leading to a massive current spike. Inrush current is asymmetrical (DC offset), and typically lasts for a few cycles (milliseconds) but can extend up to a second in some cases. Typical values for inrush current are 8-12 times the transformer's full-load current, but can be higher.


Inrush on Wye vs. Delta

While it's possible for the secondary (wye) side to have a higher inrush in some edge cases (very unusual loading or downstream equipment), it's highly unlikely to be the primary driver of your generator tripping in a black start scenario. The transformer itself is the biggest culprit. The wye side inrush will depend on the equipment connected to the switchgear.

Impact on Generator

This sudden inrush current can overload the generator, causing its protection (likely an overcurrent or undervoltage relay) to trip. Generators have limited short-term overload capacity.

1. Calculations for Inrush Current and Duration


Unfortunately, precise calculation is difficult without detailed transformer and load information. Here's the approach:
Transformer Inrush Estimation



Full Load Current (FLA) of Transformer (Primary Side)

FLA = kVA / (√3  Voltage) = 500,000 / (√3  480) ≈ 601.4 Amps


Estimated Inrush Current (I_inrush)

I_inrush = 8 to 12  FLA  = 4811.2 to 7216.8 Amps
(This is a range, actual value depends on transformer design and switching angle.)


Inrush Duration

This is trickier. It depends on the transformer's core material, size, and the impedance of the source. Generally, assume a duration of at least 5-10 cycles (83 -167 ms) at 60 Hz, but it can be longer. This is where the coordination study comes in; it would use specialized software to model this.



Load Inrush Estimation (Secondary Side)

This is harder to calculate without knowing the specific loads connected to the switchgear. You would need to look at the starting characteristics of each motor, power supply, or other equipment. In many cases, motor starting currents are the dominant inrush factor on the secondary side. Example: If you have a 100 HP motor (74.6 kW) starting across the line, its inrush can be 6-8 times its full load current. This would add to the transformer inrush.

Why a Coordination Study is Important Here

A proper coordination study uses software like SKM PowerTools or ETAP to model the entire system, including transformer saturation characteristics, generator capabilities, and relay settings. This allows for a much more accurate prediction of inrush currents and their impact on the generator and other equipment.

2. Limiting Inrush Current - Cost-Effective SolutionsHere's a ranked approach, starting with the simplest and least expensive:1.

Staggered Energization/Pre-Magnetization



Description

The problem with starting the generator, and then the transformer is that the transformer core has no residual magnetism, so you start off with the full potential for inrush current. If you were to close the primary side breaker (generator breaker), then open the battery inverter breaker, then close the battery inverter breaker, it will already have a small current flowing through it, which may reduce the inrush current.


Pros

Potentially free. Easy to implement.

Cons

Doesn't guarantee inrush reduction.2.

Generator Breaker Delay



Description

Increase the time delay on the generator's overcurrent protection relay.

Pros

Relatively inexpensive. Simple to implement.


Cons

Doesn't solve the cause of the inrush, just tolerates it. May violate coordination with downstream devices. Can still damage the generator if the overcurrent is excessive for too long. This is why you should NOT do this without a coordination study.3.

Resistors



Description

A short-term solution of adding resistors in series with the generator breaker.


Pros

Cheap and temporary

Cons

Not good for longer testing periods, as the resistors will overheat. Also, the resistors could be damaged and fail if over rated.4.

Soft Starters (for Downstream Motors)



Description

If motor inrush is a significant contributor on the secondary side, soft starters (or variable frequency drives - VFDs) can significantly reduce their inrush current.

Pros

Reduces stress on the entire system, not just the generator. Improves motor life and efficiency.


Cons

More expensive than simple solutions. Requires careful selection and installation.5.

Inrush Current Limiting Reactors (or Inductors)



Description

Install reactors in series with the transformer primary. These add impedance to the circuit, limiting the inrush current.


Pros

Relatively simple to implement. Effective in reducing inrush.

Cons

Adds losses to the system. Voltage drop during normal operation. Requires space. Can be expensive.6.

Solid-State Transformer Inrush Current Limiters (SSCLs)



Description

Modern SSCLs use solid-state switching devices (like thyristors or IGBTs) to control the energization of the transformer, gradually increasing the voltage and current to minimize inrush.

Pros

Very effective at inrush reduction. Minimal impact on normal operation.


Cons

Most expensive option. Requires careful selection and integration.

Key Recommendations1.

Prioritize the Coordination Study

This is the most important step. It will give you the data needed to make informed decisions about protection settings and inrush mitigation strategies.2.

Start with the Simplest Solutions

Try staggered energization. If that doesn't work, the reactor is a quick solution.3.

Consider Soft Starters

If the secondary side load inrush is significant, consider soft starters or VFDs on large motors.4.

Careful Relay Coordination

Any changes to relay settings must be done in conjunction with a thorough coordination study to ensure proper protection of all equipment.5.

Document Everything

Keep detailed records of all settings, changes, and test results.

A Note on Battery Inverters:While your battery inverter is providing power before the generator kicks in, its response to the transformer inrush may be different from the generator. The inverter might have its own protection that limits its output current, preventing it from tripping, or it might be able to ride through the inrush more effectively.I hope this helps! Let me know if you have more questions. Flag for review

Previous Question Next Question