Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Help me size the cable and breaker

User: Deebee101, Location: Ghana

Asked on: Sunday, September 14, 2025 at 6:46 pm EDT
Answered on: Sunday, September 14, 2025 at 6:46 pm EDT

Question: The equipment is a 5.5kW Fire Pump. The cables would be run in a PVC conduit. The cable run is about 15 meters. The location is a tropical coastal west african city let's say Monrovia. The cable is a multicore pvc insulated cable. What is the appropriate breaker size and cable size in square millimeter? We use the British system

Okay, let's calculate the appropriate breaker size and cable size for your 5.5kW fire pump in Monrovia, using British standards (likely BS 7671 or equivalent local adaptation). Given the tropical coastal environment, we'll need to account for higher ambient temperatures which affect cable ampacity.1. Calculate the Full Load Current (FLC) First, we need to assume a voltage. In West Africa, 415V (3-phase) is common, but 230V (single-phase) might also be used for smaller pumps. Let's calculate for both to be thorough: 3-Phase 415V

FLC = Power (kW) / (√3 Voltage (kV) Power Factor) We'll assume a power factor of 0.85 (a typical value for motors). FLC = 5.5 / (1.732 0.415 0.85) = 9.57A

Single-Phase 230V

FLC = Power (kW) / (Voltage (kV) Power Factor) FLC = 5.5 / (0.230 0.85) = 28.14A

2. Determine the Breaker Size
Motor Starting Current

Motors draw a significantly higher current when starting (typically 4-6 times the FLC). The breaker needs to withstand this inrush current without tripping. We'll assume a starting current of 6 times the FLC.


Breaker Type

Because this is a motor load, we'll need a breaker designed for motor starting. Common types are Type C or Type D breakers. Type D breakers have higher tolerance for inrush current and are usually preffered for fire pumps.

Overload Protection

The breaker also needs to protect against overloads. A common practice is to size the breaker at around 125% of the FLC.


3-Phase 415V

FLC: 9.57A Starting Current (6x FLC): 57.42A 125% of FLC: 11.96A Breaker Size: A 16A Type D breaker would likely be appropriate. Type C is also fine but Type D is preferrable. It's important to check the motor's nameplate for specific starting current characteristics. A 20A breaker would also be an option if starting is particularly problematic, but only if the cable can handle it.

Single-Phase 230V

FLC: 28.14A Starting Current (6x FLC): 168.84A 125% of FLC: 35.18A Breaker Size: A 40A or 50A Type D breaker would likely be needed, depending on the motor's characteristics.

3. Determine the Cable Size
Current Carrying Capacity

The cable must be able to safely carry the FLC and withstand the starting current for a short period.

Voltage Drop

We need to ensure voltage drop is within acceptable limits (typically 3% for motor circuits).


Ambient Temperature

Monrovia has a high ambient temperature. We need to derate the cable's ampacity based on the ambient temperature. Assume a typical ambient temp of 35°C to 40°C

Grouping

If other cables are in the same conduit, we'll need to apply a grouping factor, which will also lower the ampacity. This depends on the number of circuits. Let's assume no grouping for now but consider it in a real installation.


PVC Conduit

PVC conduit can further increase the cable temperature as it restricts heat dissipation.

Reference Method

Determine the reference method used for cable installation (e.g., clipped direct, in conduit on a wall, etc.). This will affect the cable's ampacity. Assuming method C.


Standard PVC Multicore Cable Sizes (Examples)

Common sizes are 1.5mm², 2.5mm², 4mm², 6mm², 10mm², 16mm², etc.

Calculations (Approximation - requires consulting cable tables)



3-Phase 415V (Using 16A Breaker)

FLC: 9.57A After derating for temperature (assuming 40°C and PVC conduit), you will likely need a cable rated for at least 13 amps. A 2.5mm² or 4mm² PVC multicore cable might be sufficient, but

you MUST consult the cable manufacturer's tables
for the specific cable type, installation method, and ambient temperature to confirm it meets the ampacity requirements. Also check the voltage drop is not excessive with a 2.5mm² cable. Single-Phase 230V (Using 40A Breaker)

FLC: 28.14A After derating for temperature, you will likely need a cable rated for at least 35A. A 6mm² or 10mm² PVC multicore cable might be required, but again,

consult the cable manufacturer's tables.
Check voltage drop.

Important Considerations & Steps


Confirm Voltage

Ensure you know the exact voltage of the electrical supply (415V 3-phase or 230V single-phase).2.

Motor Nameplate

Obtain the exact Full Load Current (FLC), Starting Current, and Power Factor from the motor's nameplate. These values are critical.3.

Cable Manufacturer's Tables

The most important step is to consult the cable manufacturer's data sheets for the specific cable you intend to use. These tables will provide the ampacity ratings for different installation methods and ambient temperatures.4.

Voltage Drop Calculation

Calculate the voltage drop using the cable's resistance and reactance per meter. Ensure the voltage drop is within acceptable limits (usually 3% maximum).5.

Regulations

Follow all local electrical codes and regulations (which are often based on or adapted from BS 7671).6.

Qualified Electrician

This calculation is for guidance only. A qualified electrician should perform the final design and installation to ensure safety and compliance. A fire pump is a critical system, and a mistake could have serious consequences.7.

Derating Factors



Temperature Derating

Cables are rated for a maximum operating temperature (e.g., 70°C). The ampacity is reduced as the ambient temperature increases.


Grouping Derating

When multiple cables are run together, the heat generated by each cable can affect the others. Grouping factors reduce the ampacity accordingly.*

Voltage Drop

Voltage drop is more significant for single-phase and smaller cable sizes. Use voltage drop tables to ensure that the voltage at the pump motor terminals is sufficient under full load conditions.

Summary Table (Estimates - Requires Verification)

| Parameter | 415V 3-Phase (Estimate) | 230V Single-Phase (Estimate)

-------------------|--------------------------|------------------------------
FLC (Nameplate) | 9.57A | 28.14A
Breaker Size | 16A Type D | 40A or 50A Type D
Cable Size | 2.5 or 4 mm² PVC | 6 or 10 mm² PVC || Conduit | PVC | PVC |


Disclaimer:
This is an approximate calculation. It is essential to consult with a qualified electrician and refer to cable manufacturer's data sheets and relevant electrical codes to ensure a safe and compliant installation. This information is provided for informational purposes only and does not constitute professional advice. Flag for review

Previous Question Next Question