Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Capping off a single conductor

User: Jimmy7, Location: Boston, MA

Asked on: Monday, September 15, 2025 at 7:39 am EDT
Answered on: Monday, September 15, 2025 at 7:40 am EDT

Question: Have you ever capped a single #12 solid with an orange wirenut? I have, and they seemed fine. I was just told they’re not rated for it.What wirenuts do you like to use when capping #16 or #18 stranded?

You're right to question this. While a single #12 solid might seem okay under an orange wire connector, it's indeed pushing the boundaries of, and likely exceeding, the UL listing. Here's a breakdown: Orange Wirenuts (#22-#14)

Most orange wirenuts are designed for a
minimum of two #14 AWG wires and a maximum of two or three #14 AWG wires or one #14 and one #18. They are generally

not rated
for a single #12 solid conductor. While the wirenut may fit, it might not provide a secure enough grip, and it definitely hasn't been tested and certified for that configuration. Over time, this could lead to loosening and a potential hazard. Why it Matters

UL listing is crucial. It ensures the wirenut has been tested to withstand the stresses of installation and operation (temperature, pull-out force, etc.) without failure, maintaining electrical integrity. Going outside the listed range voids that safety assurance.

Wirenuts for #16 or #18 Stranded Wire

For these smaller gauge stranded wires, you'll want to use appropriately sized wirenuts. Here are a few options, along with considerations:

Ideal Industries Mini-Twister or Wing-Nut (Yellow or Small Gray)

Advantages: These are compact and designed for small gauge wires. The Mini-Twister has a skirted design, and the Wing-Nut has wings for a comfortable grip. They are easier to twist on in tight spaces. They're often rated down to #22 AWG, so they will definitely work for #16 and #18. Considerations: Pay attention to the specified conductor combinations. Make sure the number of wires you're connecting falls within the allowed range.

3M Scotchlok Connectors (e.g., Red/Yellow)

Advantages: These offer reliable connections and are widely available. The 3M Scotchlok line has connectors suitable for low-voltage applications, which is very important for this thin of wiring. Considerations: Choose the correct size based on the wire gauge and number of conductors. 3M is a more expensive brand, but for good reason.

Wago 221 Series Lever-Nuts (Smallest Size)

Advantages: These are push-in connectors, which are really nice for very small conductors because they're easier to make a solid connection. They offer very good and consistent connections and are reusable. They are generally rated down to #24 AWG, so #16 and #18 are no problem. Considerations: They are more expensive than wirenuts, but for the convenience and reliability, it's worth it.

General Tips for Using Wirenuts with Stranded Wire



Pre-Twisting (Usually Not Necessary)

Modern wirenuts are designed to twist the wires together as you apply the wirenut. Pre-twisting is generally no longer recommended, and in some cases, can reduce the effectiveness of the connection. Follow the manufacturer's instructions (usually printed right on the wirenut package).

Proper Stripping Length

Strip the insulation to the length indicated on the wirenut packaging. Too much bare wire is unsafe; too little and you won't get a good connection.


Firm Twisting

Apply firm, even pressure while twisting the wirenut onto the wires. You should feel the wires drawing into the connector. The twisting action is what creates the secure mechanical and electrical bond.

Visual Inspection

After installation, tug gently on each wire to ensure it's firmly held within the wirenut. The wires should not pull out. You should also visually inspect the connection to ensure that the insulation is flush with the wirenut skirt and that no bare conductor is exposed.


Enclosed Spaces

If the connections are in an enclosed box, arrange the wires neatly inside so they're not strained or crushed.

Important Disclaimer:
I am an AI Chatbot and not a licensed electrician. Always consult with a qualified electrician for any electrical work to ensure safety and compliance with local codes. Flag for review

Previous Question Next Question