Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Aircraft Cable Linear Fixture

User: Alwayslearningelec, Location: NJ

Asked on: Monday, September 15, 2025 at 8:26 am EDT
Answered on: Monday, September 15, 2025 at 8:26 am EDT

Question: Anyone have a picture of one of these linear fixtures mounted exposed to deck? I think the two cable can possibly be shot right to deck with whip/cable from the fixture up to a box close to the fixture or maybe there's an installation where the box is attached to one of the cable. Thanks

Okay, I understand what you're looking for. You want to see examples of linear LED fixtures mounted exposed on a deck, with the wiring method visible (specifically using 2-conductor cable and how it transitions to the fixture). This is often a challenge because exposed wiring on a deck needs to be done safely and aesthetically, which can limit options.

Challenges and Considerations



Code Compliance

NEC (National Electrical Code) requires wiring on decks to be protected from physical damage and weather. This is why running NM-B (Romex) cable directly on a deck is generally
not permitted. Exposed wiring needs to be rated for wet locations and sunlight resistance.

Wet Locations

A deck is definitely considered a wet location.

Physical Protection

Decks are subject to traffic, furniture movement, and weather impacts. Wiring needs to be robust enough to withstand this.


Aesthetics

Most people don't want unsightly wiring runs across their deck.

Typical Approaches (and why they might not look exactly like what you're imagining)


Rigid or EMT Conduit

This is the most common and code-compliant method for exposed wiring on a deck. It provides excellent physical protection and is suitable for wet locations. However, it doesn't use 2-conductor cable in the way you described.2.

Liquidtight Flexible Metal Conduit (LFMC) or Liquidtight Flexible Nonmetallic Conduit (LFNC)

Often used for the "whip" connection from a junction box to the fixture. It's more flexible than rigid conduit but still provides good protection. This is often used in conjunction with THWN wires inside the conduit.3.

Direct Burial Cable (UF Cable)

While technically rated for direct burial, it's generally not recommended to run UF cable exposed on a deck surface. It's not designed to be walked on or exposed to constant abrasion. You could use it inside a protective raceway (like conduit).4.

Surface-Mounted Raceway

This is a plastic or metal channel that wires run inside. It provides protection and can be more aesthetically pleasing than exposed conduit. However, the raceway itself needs to be rated for outdoor use.5.

Proper Wet Location Wiring

Wiring should be THHN or THWN. Junction boxes and connections need to be weather resistant.

Why Finding Exactly What You Described Is Difficult

The scenario you're describing (2-conductor cable run directly to the deck surface, with a short whip up to the fixture, possibly with a box attached to the cable) is likely not a compliant or commonly implemented solution because it is very hard to do with code. It would violate a lot of different electrical codes. The short run up to the fixture is generally from a junction box to make the electrical connection.

Alternative Interpretation and Possible Scenarios

Let's break down scenarios where your description might be partially accurate, or where you might see something similar:

Low-Voltage Lighting

If the linear fixture is low-voltage (e.g., 12V or 24V), the rules are a bit more relaxed. You
might see low-voltage cable (rated for outdoor use) running along the deck surface, secured properly and protected. However, even with low-voltage, you'd still want to protect it from physical damage. A proper power supply should be mounted somewhere else and not exposed to the elements.

Temporary Lighting (Not Recommended for Permanent Installation)

You might see temporary installations (like holiday lighting) that use extension cords or similar wiring methods. These are generally not code-compliant for permanent installations and can be dangerous.

"Creative" (Incorrect) Installations

Unfortunately, you
might find examples of DIY installations that are not done correctly and violate code. These are unsafe and should not be emulated.

Recommendations
1. Consult with a licensed electrician. They can assess your specific deck situation and recommend the safest and most code-compliant wiring method for your linear fixture.
2. Prioritize safety and code compliance. Don't cut corners on electrical work.3. Consider aesthetics. There are ways to run wiring safely and attractively on a deck.

Summary: While I can't provide an image of the
exact* scenario you described (because it's likely not code-compliant), the information above provides context, alternative approaches, and highlights the importance of safety and proper installation. Remember to consult with a qualified electrician for your specific needs. Flag for review

Previous Question Next Question