User: Little Bill, Location: Tennessee NEC:2017
Asked on: Tuesday, September 16, 2025 at 12:42 pm EDT
Answered on: Tuesday, September 16, 2025 at 12:42 pm EDT
Question: This relates to my previous thread(s) concerning 3ph equipment. I have more info to work with.The oven currently runs on 480V (from a transformer). It is fed with 3ph but the elements are just single ph.There was some extra/spare elements there, so I measured the resistance on them. They measured19.4 ohms on the elements.The current draw that I measured on the working elements was 34A. There are 12 elements in the oven.The oven is being moved to a new building that will only have 120V/240V. They will not have 3ph.What I want to do is just use the 240V single ph and rewire the elements.I came up with around 16Kva for the power as it runs now. But that doesn't exactly match the resistance I measured on the spare elements.480Vsq/19.4ohms = 11.9KvaI was only able to measure the current but not the voltage as the guy was leaving, so the voltage may not be exactly 480V since its from a 240V to 480V transformer.I suppose my questions are:Do I have to take the 12 elements and consider them parallel circuits, or is the 19ohms total R?If this requires nodal analyzes, it's been too long for me to remember how to do that.Or to jump ahead and just ask what my current draw would be at the new building using 240V instead of 480V?The elements currently only come on for 12 secs, then off. So if the voltage is reduced to 240V, would that give enough heat if the time were increased?Keep in mind, I would only be using 2 legs instead of 3 legs since the new building is single ph.Ask me any info that I may have left out.
Okay, let's break this down and figure out the best approach to adapting your oven. You're right, there are some inconsistencies, and we need to get them sorted out.
Understanding the Current Configuration 480V Supply
The oven currently runs on 480V, which is derived from a transformer likely stepping up from 240V or another voltage.
Single-Phase Elements
Despite being in a 3-phase system, each heating element is wired as a single-phase load. This is important.
Element Resistance
You measured 19.4 ohms on the spare elements. This is a crucial piece of information.
Current Draw
34A current draw per element is what you measured.
12 Elements
There are 12 elements in total.
On/Off Cycling
The elements are cycled on for 12 seconds and then off. This likely controlled by a temperature controller.
Addressing the Inconsistencies KVA Discrepancy
You calculated 16 kVA and 11.9 kVA. There are discrepancies. The first estimation for 16kVa was from name plate. I didn't measure that myself. The 11.9Kva calculation is (480 480)/19.4 = 11,876 I suspect the voltage at the element is lower than 480V. It can be measured later. The nameplate Kva, could also be high if the oven never runs all elements at the same time.
Adapting to 240V Single-Phase
This is where the real work begins. Here's the core idea:1. Re-wiring is Necessary
You absolutely need to re-wire the elements. Simply connecting the existing configuration to 240V will drastically reduce the power output and likely not provide enough heat.2.
Series/Parallel Combinations
The key to making this work on 240V is to wire the elements in a series/parallel arrangement to match the 240V supply while maintaining a reasonable current draw per element.3.
Calculate Target Resistance
To get the same power out of each element at 240V as they're currently getting (assuming 34A @ 480V), we can do these calculations. (Assuming you want to keep the same amount of total heat output.) Current Power: P = V I = 480V 34A = 16,320 Watts Target Resistance: R = V^2 / P = 240V 240V / 16,320 Watts = 3.529 ohms (approximately) To get the oven to produce the same heat output as it does now, each element would need to produce 16,320W if it were connected to 240V. And to do that, each element would need a resistance of 3.529 Ohms.
4.
Series/Parallel Configuration
You have 12 elements, each with a resistance of 19.4 ohms. You could arrange them in series and parallel configurations so that each branch has a resistance of 3.529 ohms. To get 3.529 ohms on each branch, you would need to put 5.5 elements in parallel with one another. ( 19.4 / 5.5 = 3.529 ) This isn't possible to achieve perfectly unless we cut off some of the resistive wire in 1/2 of the elements. It would require a lot of modification. Alternatively, you could put elements in series with one another until you reached the correct voltage and resistance. First we calculate the voltage drop across the element. Voltage per element is: V = sqrt( P R ) = sqrt (16320 19.4) = 562.6V With the element at 19.4 ohms, it requires 562.6V to produce the same heat as it did before. Since the new building has 240V, putting elements in series is not a great option. Another option would be to put all 12 elements in parallel with one another. To do that you need to put them in series. V = I R 240V = I 19.4 I = 12.37A P = I V = 12.37 240 = 2969 The heat produced with elements in series is 2969 watts per element. That is much lower than the original heat being produced, so the oven may not get as hot. You could add a transformer to boost the voltage.5.
Current Calculation
Total Current = 12 elements 12.37 Amps = 148.44 amps.
Important Considerations & Next Steps
Electrical Code
CRITICAL. Before doing anything, consult with a qualified electrician who is familiar with your local electrical codes. Rewiring high-power equipment can be dangerous and must be done to code. Overcurrent Protection
The circuit breaker/fuse size for your new 240V circuit must be appropriately sized to handle the calculated current draw. 150% or 200% over the maximum current is recommended. So it would be over 222 amps.
Wire Gauge
The wiring (gauge and insulation type) needs to be rated for the calculated current and the operating temperature.
Enclosure/Junction Boxes
Make sure any new wiring is contained within appropriate enclosures and junction boxes.
Revised Recommendation
Since you want it to run the same amount of heat as it did before, you would have to modify each element or find an alternative.Putting the elements in series or parallel will produce a lower temperature.Since there isn't much space for another transformer, I would suggest purchasing 240V elements that have the same shape and dimensions as the ones that you have.
In Summary
The math is tricky and you must consider the amperage.Also, be aware that the existing timer and temp controller, etc. may need to be changed out as well.Your safety is paramount. This is a job that should be done by a qualified electrician. Flag for review