Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Two main breaker panels service feed through single conduit and pass-through from Utility meter enclosure question

User: harrelsc, Location: Florida

Asked on: Tuesday, September 16, 2025 at 3:29 pm EDT
Answered on: Tuesday, September 16, 2025 at 3:34 pm EDT

Question: Is this setup allowed for 2 - 150amp main breaker panels and single utility meter enclosure, getting conflicting information. Single 2in sch40 conduit connection between utility enclosure and 1st panel containing (6) 2/0 Aluminum service cables. Three of these cables passes-though the 1st main breaker panel to the 2nd main breaker panel through another 2in. sch40 conduit. Each 150amp panel is wired with 2-hot, 1-neutral cable. No other cable types pass through the same service cable conduit. The feeder cables to the respective sub-panel cabinets pass through their own separate conduit. Main breaker #1 with the pass-through service cables for main breaker #2 will be labeled indicating the pass-through service cable disconnect is located in main breaker panel #2.

Okay, let's break down this setup and address the potential code compliance issues. You are correct that this is a situation where you might get conflicting information, as interpretations can vary.

Summary of the Setup



Single Utility Meter Enclosure

Good.


Two 150A Main Breaker Panels

Acceptable if the load calculation permits (more on that below).

2" SCH40 Conduit from Meter to Panel 1

Contains (6) 2/0 Aluminum service cables.


2" SCH40 Conduit from Panel 1 to Panel 2

Contains (3) 2/0 Aluminum service cables (pass-through).

Each Panel Wired

2 Hot, 1 Neutral.


No other cable types

Only service entrance cables in the described conduits.

Panel Labeling

Clear labeling of pass-through disconnect location in Panel 2.

Analysis and Potential Issues Based on NEC (National Electrical Code)


Load Calculation (Critical)

The absolute
most critical aspect is the load calculation.

The sum of the ratings of the two main breakers
cannot exceed the calculated service load.
This is a common misunderstanding. You are not allowed to simply add the breaker sizes together and assume that's okay. You must perform a proper load calculation according to NEC Article 220, considering the square footage of the dwelling, appliances, heating/cooling, and other connected loads. If the load calculation exceeds 150A, you are in violation, regardless of the conduit fill.2. Service Entrance Conductors (2/0 Aluminum)

2/0 Aluminum is typically rated for 100 Amps at 75°C. 310.16 and 310.15(B)(16). To feed a 150 amp service would require 250 kcmil aluminum minimum.
3.


Number of Service Disconnects

NEC 230.71(A) states that the service disconnecting means shall consist of not more than six switches or sets of circuit breakers, or a combination of not more than six switches and sets of circuit breakers, mounted in a single enclosure, in a group of separate enclosures, or in or on a switchboard. Since both panels contain the main breakers with disconnects it is technically in compliance with the NEC's (National Electrical Code) 6 disconnect rule.
4.


Conduit Fill

NEC Chapter 9, Table 4, gives conduit fill limitations. We need to calculate the cross-sectional area of the conductors and compare that to the allowable fill for 2" SCH40 conduit.
Based on information found from manufacturers, the approximate outside diameter (OD) of 2/0 Aluminum XHHW or USE cable is 0.685 inches. Area = π (radius)^2 = π (0.685/2)^2 ≈ 0.369 sq. in. per conductor For (6) conductors: 6 0.369 sq. in. = 2.214 sq. in. total For (3) conductors: 3 0.369 sq. in. = 1.107 sq. in. total 2" SCH40 conduit allows 40% fill of 1.358 sq. in. according to NEC Chapter 9, Table 4.

Therefore, the conduit is too small and not NEC compliant.
5. Pass-Through Conductors

The pass-through of conductors from Panel 1 to Panel 2 is allowed, but the conductors must be sized appropriately for the load served by Panel 2. You cannot just use undersized conductors simply because the main breaker in Panel 1 is smaller.
6.


Clearance in Panel 1

Be sure there's sufficient space in Panel 1 for the conductors to pass through and make connections to the main breaker. Crowding can lead to overheating and code violations.7.

Labeling

The labeling of the pass-through disconnect is crucial and meets NEC requirements for clarity.

Recommendations


Perform a Thorough Load Calculation

This is non-negotiable. It will determine if your current setup is even viable. Engage a qualified electrician if you're not comfortable doing this yourself.2.

Correctly Size Your Conductors

Make sure the 2/0 Aluminum is correctly sized.3.

Increase Conduit Size

Based on the amount of service entrance cables your running, the 2" sch40 conduit is too small.4.

Consult Local Inspector

Even if you believe your setup meets the NEC, the local electrical inspector has the final say. Discuss your plan with them before starting the work to avoid costly rework. They may have specific local amendments to the NEC that you need to follow.

In summary, the 2" conduit to the panels is likely too small for the (6) 2/0 aluminum service entrance cables. Load calculation must be performed to verify compliance.
It's strongly advised to consult a qualified electrician and the local electrical inspector to ensure your setup is safe and code-compliant. This is electrical work, and safety is paramount. Flag for review

Previous Question Next Question