Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Wiring method to 2000A transfer switch, 10 feet outside

User: electrofelon, Location: Cherry Valley NY, Seattle, WA

Asked on: Thursday, September 18, 2025 at 11:44 am EDT
Answered on: Thursday, September 18, 2025 at 11:45 am EDT

Question: I have to come out of a 2000A switchboard, theu a CMU wall to a 2000A transfer switch outside. There is about 10-12 feet between the wall and the transfer switch. There is already a large box mounted on top of the switch board. The equipment is oversized, with 3 years of demand data showing max demand of 136KW. (377A). Thus i will probably reduce the feeder down to maybe 1200A. I can probably get 2 sets of 600Al in a 4" with a reduced neutral, in which case that would be 4 conduits total (2 out, 2 back in). We're just toying with other options. What about using a 3r wire way? I can just cut a hole in the CMU wall, use a wire way and box flange to come into the back of the inside box, then nipple put the bottom into the top of xfer switch. Another option might be cable tray, but that doesn't seem like a great option due to transitioning from inside to outside and having to go into the top of the switch. Any other thoughts or ideas? Should I just run the conduits?

Okay, this is a classic electrical engineering challenge! Let's break down the options and considerations for your 2000A to 1200A feeder tap. I'm going to prioritize safety, code compliance (NEC), and practical installation.

Key Considerations



Ampacity & Voltage Drop

You're proposing to downsize the feeder to 1200A based on demand data. This is a good starting point, but
absolutely verify your calculations and deratings. Ambient temperature, grouping of conductors, and conduit fill all affect ampacity. Voltage drop is also critical, especially with a run of 10-12 feet.

Neutral Sizing

Reduced neutral is common, but carefully calculate the required neutral ampacity based on anticipated harmonic content and unbalanced loads. Don't undersize it!

Environmental Factors

You're dealing with an indoor-to-outdoor transition, so weatherproofing is paramount. Consider rain, snow, ice, UV exposure, and temperature extremes.


Code Compliance

You must adhere to the National Electrical Code (NEC). This includes conductor ampacity, conduit fill, grounding, bonding, and suitable raceway types. Consult Article 310 for Ampacity, Chapter 3 for Wiring Methods and Materials.

Accessibility & Maintainability

Future access for inspection, maintenance, and potential upgrades should be factored in.


Cost

While not the only driver, cost is a factor. Consider material, labor, and long-term maintenance.

Feeder Tap Rules

Check NEC 240.21 for feeder tap rules. If you are tapping a 2000A bus to feed a 1200A load, you must comply with the length requirements in 240.21(B).


Short-Circuit Current Rating (SCCR)

Verify that the transfer switch's SCCR is sufficient for the available fault current at its location. The downsizing of the feeder does not necessarily mean a reduction in the available fault current.

Analysis of Options


Conduit (2 sets of 600 kcmil in 4" with reduced neutral)



Pros

Well-established and understood method. Good physical protection for conductors. Relatively easy to seal against weather at the CMU wall penetration. Easy to support. Conduit fill is well understood and documented. Cost effective

Cons

Requires four conduit runs (2 in, 2 out). This can be labor-intensive to install. Bending large conduit can be challenging. Pulling large conductors through multiple bends is difficult. Neutral conductor size reduction may not be permitted for service-entrance conductors.

Considerations

Use properly sized and rated conduit bodies (LB, LL, LR) to minimize bends and pulling difficulty. Thoroughly clean and lubricate conductors during pulling. Ensure the conduit is properly grounded and bonded.2.

NEMA 3R Wireway



Pros

Potentially faster installation than multiple conduits. Easier to pull conductors through a straight wireway run. More space for conductors than conduit.

Cons

Wireway ampacity derating is a critical factor. You must carefully calculate the allowable ampacity based on the number of conductors and the wireway's cross-sectional area and ventilation. NEC 376.22, and 376.
23. Sealing the wireway against weather at the CMU penetration and the transfer switch entry can be tricky. Use appropriate rain-tight connectors and sealing methods. Wireway support is crucial, especially with heavy conductors. Use properly sized and spaced supports. Bending wireway is not as easy as bending conduit. The wireway itself may not be as robust against physical damage as conduit. Transition from switchboard box to wireway can be complicated.


Considerations

Select a wireway with adequate ventilation to help with heat dissipation. Use a wireway with a hinged cover for easy access. Ensure the wireway is properly grounded and bonded. The section entering the building must be suitable for indoor environments The section entering the Xfer switch must be suitable for outdoor environments3.

Cable Tray



Pros

Good for long runs and large numbers of cables. Allows for easy inspection and maintenance.

Cons

Not ideal for short runs like yours (10-12 feet). Transitioning from inside to outside and into the top of the transfer switch is awkward. Weatherproofing can be difficult. May require more support than other options. Cable tray is typically more expensive than conduit or wireway.

Considerations

You would need to use cable suitable for cable tray installation (e.g., Type TC). Ensure the cable tray is properly grounded and bonded. Cable tray is more susceptible to damage.

Recommendation

Given the short run and the need for a reliable, weatherproof installation,

I would lean towards the conduit solution (Option 1).
Here's why: Proven Reliability

Conduit systems are a well-understood and widely used method for electrical installations.


Good Physical Protection

Conduit provides excellent physical protection for the conductors.

Easy to Weatherproof

Properly installed conduit and fittings are easy to seal against the elements.


Cost-Effective

Conduit is generally less expensive than wireway or cable tray.

Familiar Installation Techniques

Most electricians are comfortable working with conduit.

Specific Steps & Considerations


Detailed Calculations

Perform thorough ampacity, voltage drop, and neutral sizing calculations
before selecting conductors and conduit size.2.

Feeder Tap Rules

Comply with feeder tap rules in 240.21.
3.


Coordinate with Transfer Switch Manufacturer

Confirm the entry requirements and available space at the top of the transfer switch.4.

CMU Wall Penetration

Core drill a clean hole through the CMU wall. Use a sleeve and sealant to ensure a weatherproof seal around the conduits.5.

Conduit Bodies

Use appropriate conduit bodies (LB, LL, LR) to minimize bends and make pulling easier.6.

Weatherproof Fittings

Use weatherproof conduit fittings and connectors.7.

Grounding and Bonding

Ensure the entire system is properly grounded and bonded according to NEC Article 250.8.

Inspection

Schedule an inspection with the local electrical inspector to ensure compliance with all applicable codes and regulations.9.

Labeling

Label all conduits and equipment clearly.

If you absolutely want to consider Wireway


Detailed Calculations

NEC 376.22 requires that the sum of the cross-sectional areas of all conductors at any cross section of the wireway not exceed 20% of the interior cross-sectional area of the wireway.
2.


Derating

Conductors in wireway must comply with 310.15(C)(1) and NEC Table 310.15(C)(1). This often requires substantial derating.
3.


Choose a Wireway Rated for Outside Use

Wireway used outside must comply with 376.10 and be suitable for wet locations.
4.


Grounding and Bonding

Ensure the entire system is properly grounded and bonded according to NEC Article 250.5.

Sealing

Weatherproof sealant will be required between all sections of the wireway, at the building penetration, and on top of the transfer switch.

Important Reminders



Licensed Electrician

This work must be performed by a qualified and licensed electrician.

Permitting

Obtain all necessary permits before starting the work.


Safety:
Follow all safety precautions during installation.I hope this comprehensive analysis helps you make the best decision for your project! Good luck! Flag for review

Previous Question Next Question