User: Voltaire, Location: Vermont
Asked on: Monday, September 22, 2025 at 9:48 am EDT
Answered on: Monday, September 22, 2025 at 9:56 am EDT
Question: Needing to supply power to a control box for 2x 15,000 Watt immersion heaters (resistive load). Service is 3 phase 208v. Heaters will only be on for ~1 hour per day. Total Amp draw of both heaters is around 83. I've sized the circuit for 100 Amp breaker, 3x #3 AWG hots and 1x #6 AWG ground, 1-1/4" EMT.Looks like I have 2 options:Make a 100 amp receptacle in a box for Hubbell pin/sleeve type connectors. This is the more preferred way as it gives flexibility for the placement of the control box and makes it easy to take down for servicing. I'd like to keep the junction box for this receptacle as small as possible. Questions arise as to how small this junction box can be since it's unclear if and how NEC 314.28 applies as there will be no wires passing through the box. All conductors will terminate at the receptacle. I can also have the conduit enter the back of the box (through the wall and opposite a cover plate), bringing Table 312.6(A) into effect.Pipe the 1-1/4" EMT directly to the box. Less desirable for reasons stated above. It also makes the control box part of the building wiring, which would ideally be avoided. Not sure of any subtle or lesser known code quirks this might bring up. If this method is necessary, is there a good way to transition from EMT to NM flex conduit without requiring a large box as per NEC 314.28?Are both of these options viable? Which would you prefer? This was typed a bit fast and any confusion can be cleared up, just ask. Thanks!
Okay, let's break down your options for powering your immersion heaters and address your concerns.
Understanding the Key Considerations Load Calculation & Wiring
Your sizing for the circuit (100A breaker, #3 AWG, #6 AWG ground) is correct for the 83A continuous load (83A 1.25 = 103.75A, so 100A breaker is acceptable). Your EMT sizing is also adequate.
NEC 314.28 (Pull/Junction Box Sizing)
This is the crucial section for your junction box question, especially when using conduit. It's about the minimum size of boxes to accommodate the bending radius and layout of conductors entering and exiting the box.
Serviceability and Flexibility
Your desire for a receptacle-based connection is understandable. It simplifies maintenance and allows for easier relocation of the control box if needed.
Continuous Load
Because your load is on for 1 hour a day it does not need to be considered a continuous load.
Option 1: Receptacle with Pin/Sleeve Connector (Your Preferred Method)
This is viable and generally the preferred approach for serviceability. Here's the breakdown: Viability
Absolutely. It's a common and acceptable method for connecting equipment.
Junction Box Sizing (NEC 314.28)
This is where it gets nuanced. If NO wires pass through the box (all conductors terminate at the receptacle), NEC 314.28 DOES NOT APPLY. The box only needs to be large enough to: Accommodate the 100A receptacle and its connections. Provide adequate space for wire bending radius within the box according to NEC 314.24 Meet the volume requirements based on the number and size of conductors entering the box (NEC 314.16). Be suitable for the environment (e.g., NEMA 4X if outdoors or in a damp environment). EMT Entry
Since you can enter through the back of the box, you are correct that Table 312.6(A) then takes precedence. This refers to working clearance requirements, not box sizing. The key is ensuring you have adequate access and working space in front of the box to safely make connections and maintain the receptacle. It also ensures that if you need to work in the box with the power on there's enough room to prevent arc flash.
Box Selection
Since NEC 314.28 doesn't apply, you can use a relatively small junction box. Consider the following:
Physical Size
Measure the receptacle's dimensions (including space for wire terminations). Add sufficient space around it for bending conductors and making connections. A box that is too small can lead to pinched wires and difficult connections, both of which are safety hazards.
Volume
Calculate the cubic inch volume required based on the number and size of conductors (NEC 314.16). #3 AWG requires 2.25 cubic inches per conductor, and #6 AWG requires 1.5 cubic inches per conductor. For 3 hots and 1 ground, that's (3 2.25) + 1.5 = 8.25 cubic inches. It's good to add a little extra space for ease of work.
Material
Choose a material appropriate for the environment. Metal (steel, aluminum) or non-metallic boxes are both acceptable, as long as they are listed for the purpose.
Knockouts
Ensure the box has appropriate knockouts for your 1-1/4" EMT connector.
Option 2: Direct EMT Connection to Control Box
This is also viable, but generally less desirable for the reasons you stated. Viability
Yes, but...
Less Flexibility
Makes the control box a fixed part of the electrical system.
Potential Code Issues
314.28 Concerns
If you're running the 1-1/4" EMT directly into the control box,
314.28 will likely apply because the conductors will likely "pass through" the box. This means the control box would need to meet the minimum size requirements based on the conduit size and the number of conductors entering/exiting. This can result in a much larger control box than you would otherwise need. The NEC states that if you have to pull wires through the box the minimum length of the box has to be 8 times the size of the largest raceway entering the box in a straight pull. For an angle pull it becomes even more complex. EMT to Flex Conduit Transition (If Necessary)
You asked about transitioning from EMT to NM flex. It's generally permissible to transition from EMT to flexible metal conduit (FMC) or liquidtight flexible metal conduit (LFMC) for the final connection to equipment. The transition requires appropriate fittings listed for the purpose. You don't necessarily need a large junction box at the transition, but you do need a suitable enclosure to house the transition fittings. However, consider the implications of introducing FMC/LFMC into the system – is it really necessary, or can you achieve sufficient flexibility with properly installed EMT? If it's necessary to reduce vibration or provide a little bit of movement, an expansion coupling can also be considered.
Recommendation
I strongly recommend
Option 1 (Receptacle with Pin/Sleeve Connector). Here's why: Serviceability
Easy disconnection for maintenance or replacement of the heaters or control box.
Flexibility
Allows for repositioning the control box if needed.
Smaller Enclosure
Avoids the stringent sizing requirements of NEC 314.28 if no wires pass through the box.
Safety
Proper pin/sleeve connectors are designed for the amperage and voltage, providing a safe and reliable connection.
Key Steps for Option 1
Select a 100A-rated, 3-phase, 208V pin/sleeve receptacle and matching plug. Ensure they are UL-listed and suitable for the environment (e.g., NEMA rating).2. Choose a suitable junction box. Size it based on: Receptacle dimensions Wire bending space within the box Minimum volume requirements per NEC 314.16 Environmental conditions3. Install the junction box. Mount it securely.4. Connect the EMT to the junction box. Use appropriate fittings.5. Wire the receptacle. Connect the #3 AWG conductors to the appropriate terminals on the receptacle, and the #6 AWG ground wire to the grounding terminal.6. Test the connection. Use a multimeter to verify proper voltage and ground continuity.
Important Notes
Local Codes
Always check with your local electrical inspector for any specific requirements or interpretations of the NEC in your jurisdiction.
Licensed Electrician
This work should be performed by a qualified and licensed electrician. Working with high-voltage, high-amperage circuits is dangerous and requires expertise.*
Thorough Inspection: Have the completed installation inspected by your local electrical inspector before putting the system into operation.By following these guidelines, you can create a safe, reliable, and serviceable power connection for your immersion heaters. Good luck! Flag for review