Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Feeding service wire through panel back exit

User: Stuntman, Location: Midwest

Asked on: Monday, September 22, 2025 at 3:44 pm EDT
Answered on: Monday, September 22, 2025 at 3:44 pm EDT

Question: I have a situation with a double lug meter that needs to service 2 panels: One 200A drop directly to a disconnect (Main Breaker), then underground to a subpanel via feedthrough lugs. The second run is for a main panel on the other side of the wall as the meter and disconnect. I am hoping I can keep this clean by running both sets of service wires through a 3" offset to the disconnect, then popping a hole in the back of the disconnect to service the main panel on the other side of the wall.1. Is this a bend radius concern, coming into a main breaker panel then exiting through the rear of the panel? I have seen this done in previous installations but never considered if that was too tight of a bend. Since these are very short runs, I could certainly entertain copper for the interconnects to reduce the size.2. IIRC, a conduit length less than 24" (conduit offset) negates the need for conductor derating?

Okay, let's break down this double-lug meter situation and address your concerns.

Understanding the Setup

You have a double-lug meter feeding two main panels. One panel gets its power via a 200A disconnect (with a main breaker) and an underground feed to a subpanel. The other panel is directly fed through the wall. Your idea is to use a 3" offset to route both sets of service conductors into the disconnect, then exit the back of the disconnect to feed the second main panel.

Analyzing Your Concerns1. Bend Radius and Disconnect/Panel Configuration



Bend Radius is a MAJOR Concern

You're right to be concerned about this. Service entrance conductors are typically very large and stiff. Squeezing them through a tight offset,
into a disconnect, and then immediately making a 180-degree turn to exit the back presents a significant risk of violating the conductor's minimum bending radius. Violating the bend radius can damage the insulation, leading to shorts, ground faults, and potential fires.

NEC Mandates

NEC 312.6 (and the associated Informational Note 1) specifies minimum wire bending space at terminals. This section dictates the minimum amount of space for bending conductors inside enclosures. You must consider the overall length required for the wire to reach the terminals in the disconnect, plus the length needed to make the turn to exit the back. The NEC does not address this.

Practical Considerations

Even with copper, if you're using 250 kcmil or larger conductors, the bending radius can still be substantial. Physically maneuvering those conductors in such a tight space will be very difficult, and likely impossible without causing stress on the conductors and terminations.


Alternative Solutions



Separate Raceways

This is the
most compliant and generally safest approach. Run separate conduits (or appropriate service entrance cable) from the meter directly to each panel.

Larger Enclosure

If you absolutely must have both sets of conductors pass through one enclosure, select a significantly larger junction box or trough with ample space for bending. Ensure it's properly sized for the number and size of conductors, and suitable for the environment. A pull box mounted on the exterior wall adjacent to the disconnect may be the best approach.

Service Entrance Rated Tap Box

This will involve the most cost and connections.2.

Conduit Fill and Derating (Conduit Nipples Less Than 24")



Correct, but Limited Relief

You are correct that NEC 310.15(B)(3)(a) (Adjustment Factors) provides a limited exception for short conduit nipples (less than 24 inches). The section generally requires that conductors in the same raceway be derated to account for heating effects. If the length is 24" or less, the NEC does not generally require you to use the adjustment factors in Table 310.15(B)(3)(a).

Derating is Usually Still Required

However, this exception does not mean you can ignore conductor ampacity. You still must size the conductors to meet or exceed the load requirements (NEC 215.2, 220, 230) and the overcurrent protection (NEC 240). The 24" exception only addresses the additional derating that would be required if the conductors were bundled in a long conduit run.

Conduit Fill

Don't forget to calculate conduit fill to ensure you're not exceeding the maximum allowable fill percentage (NEC Chapter 9, Table 1). This is important, regardless of conduit length. For service entrance conductors, it is highly likely you will not be able to fit the conductors in a 3" conduit, based on the amount of conductors and the required ground (EGC).

Conduit Fill Examples

You haven't specified conductor size or type, so it's difficult to be specific. However, a 3" conduit filled with 6 sets of (for example) 3/0 AWG THHN copper conductors (six hots, six neutrals, and one ground) would likely
exceed the allowable fill.

In summary, while the short conduit nipple exception can provide some minor relief from derating, your primary concern should be the physical bend radius of the conductors and adequate working space. Using a 3" offset as described is very likely to be a violation of the NEC and create a dangerous installation.
Recommendations1. Consult a Licensed Electrician

This is a complex situation. A qualified electrician can assess the specific conditions, local codes, and equipment, and design a safe and compliant installation.2.

Separate Raceways

Run separate conduits/cables from the meter to each panel. This eliminates the bending radius problem and ensures adequate working space.3.

Pull Box

If separate raceways are not possible for some reason, use a large junction box/pull box mounted externally to provide the required bending space. Then, use a short nipple to connect the pull box to the disconnect. Ensure the pull box is properly sized per NEC 314.28.
4.


Oversized Enclosure

If you absolutely must pass conductors through a single enclosure, use a
significantly* larger enclosure (e.g., a trough) that provides ample space for bending and termination.5.

NEC and Local Codes

Adhere strictly to the National Electrical Code (NEC) and any applicable local codes. Pay close attention to articles related to service entrances (Article 230), wiring methods (Chapter 3), and conductor ampacity and derating (Article 310).6.

Aluminum vs. Copper

Keep in mind that Aluminum is a much larger overall diameter than Copper, and is substantially cheaper to purchase for service entrance conductors.

Important Safety Note:
Working with service entrance conductors is extremely dangerous. Always disconnect power at the meter before working on any service equipment. If you are not a qualified electrician, do not attempt this work yourself. Flag for review

Previous Question Next Question