Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Grid tie PV with Generator back up/

User: Sierrasparky, Location: USA

Asked on: Monday, September 22, 2025 at 8:34 pm EDT
Answered on: Monday, September 22, 2025 at 8:35 pm EDT

Question: What is the proper way to add a portable generator to a home with PV grid tie Don't want the PV back-feeding the genny. Someone said add a Normally closed relay on the PV tie to the main panel that opens when the Generator is run?

You're right to be concerned about backfeeding! Connecting a generator to a PV system improperly can damage your equipment, endanger utility workers, and violate electrical codes. The solution involves a transfer switch to isolate the PV system and connect the generator safely. Here's a breakdown of why and how

Why a Transfer Switch is Essential
Preventing Backfeed

The biggest danger is backfeeding. Your PV system
normally sends power to the grid. If the grid goes down (power outage), your PV system is supposed to shut down as well (anti-islanding protection). If you connect a generator and the PV system is still active, the PV power can flow back into the generator. This can damage the generator, create a fire hazard, and energize the utility lines, endangering lineworkers who are expecting them to be de-energized.

Safe Isolation

A transfer switch physically isolates either the grid OR the generator from your home's electrical system. It ensures that only ONE power source is connected at a time. This is crucial for safety.

Code Compliance

Electrical codes
require a transfer switch or similar approved method when connecting a generator to a grid-tied system. Without it, your installation is not to code and could have insurance implications.

Why a Relay (Alone) Isn't Enough


While a relay
might seem like a simple solution, it's generally not a safe or code-compliant solution on its own. Here's why: Reliability

Relays can fail. If the relay fails closed when the generator is running, you have the same backfeed problem. Transfer switches are designed for higher reliability and often have visual indication of their position.

Complexity

You'd need to design a system that reliably detects generator power and triggers the relay instantly. Any delay could cause problems.


Listing/Certification

Relays are not typically listed for this specific purpose in a home power system. Transfer switches are, because they've been tested for this exact scenario.

The Proper Solution: A Transfer Switch


The best and safest way to integrate a generator with your PV system is to use a transfer switch. There are two main types:1. Manual Transfer Switch



How it works

You manually switch between the grid power and generator power. You turn off the main breaker, then flip the transfer switch to the generator position, and then turn on breakers for the circuits you want to power.


Pros

Less expensive, simpler to install, no automatic features to fail.

Cons

Requires you to be physically present to switch power. You need to be familiar with the switch's operation and safety procedures.


Important

Make sure you know your generator's wattage and don't overload it.2.

Automatic Transfer Switch (ATS)



How it works

When the grid power fails, the ATS automatically detects the outage, starts the generator (if it has an automatic start feature), and switches the house over to generator power. When grid power returns, it switches back automatically.


Pros

Convenience, seamless transition during power outages, can be used with generators with automatic start.

Cons

More expensive, more complex to install, requires a generator with automatic start capability (in most cases).


Important

Consider fuel management (e.g., a propane tank with enough capacity) for extended outages.

Key Considerations When Choosing a Transfer Switch
Amperage Rating

The transfer switch must have an amperage rating that is equal to or greater than the main breaker in your panel.


Load Capacity

Determine the total wattage of the appliances and lights you want to run on the generator. The transfer switch and generator must be able to handle that load.

Installation

Unless you have significant electrical experience,

hire a qualified electrician
to install the transfer switch. This is not a DIY project due to the safety risks. Compatibility

Ensure the transfer switch is compatible with your generator's voltage and amperage.

Listing/Certification

Look for a transfer switch that is UL-listed or ETL-listed for safety and performance.


Neutral Switching

Transfer switches can be switching or non-switching of the neutral conductor. A non-switching neutral may cause nuisance tripping of GFCI breakers in your system. Switching the neutral disconnects the neutral from the grid, which is desired in many cases.

Steps for Adding a Generator with a Transfer Switch to a PV System
1. Consult with Professionals

Talk to a qualified electrician and your solar installer. They can assess your specific situation, recommend the appropriate transfer switch and generator size, and ensure a safe and code-compliant installation.2.

Determine Your Power Needs

Figure out what appliances and lights are essential during a power outage. Calculate their total wattage to determine the necessary generator size.3.

Choose a Transfer Switch

Based on your budget, needs, and professional advice, select a manual or automatic transfer switch with the correct amperage and features.4.

Install the Transfer Switch



Hire a licensed electrician
to install the transfer switch according to the manufacturer's instructions and local electrical codes. This involves connecting it to your main electrical panel and the generator's input.5. Connect the Generator

Follow the generator's instructions to connect it to the transfer switch's input receptacle.6.

Test the System

After installation, thoroughly test the system to ensure it works correctly. Simulate a power outage and verify that the transfer switch switches to generator power and back to grid power when utility power is restored.7.

Understand Operating Procedures

Make sure you understand how to operate the transfer switch, start and stop the generator, and monitor the load.

Important Safety Notes
Carbon Monoxide

Generators produce deadly carbon monoxide gas.

Never
run a generator indoors or in a partially enclosed space like a garage. Place the generator outdoors in a well-ventilated area, away from windows and doors. Install carbon monoxide detectors in your home.
Grounding

Properly ground the generator according to the manufacturer's instructions and electrical codes.

Fuel Storage

Store fuel safely in approved containers, away from heat sources.


Maintenance

Maintain your generator according to the manufacturer's instructions. Regularly check the oil level, air filter, and spark plug.

In Summary


Adding a generator to a home with a grid-tied PV system requires a transfer switch for safety and code compliance. Using a relay alone is generally not sufficient. Consult with qualified professionals, choose the right type of transfer switch, and follow proper installation and operating procedures to ensure a safe and reliable system. Prioritize safety above all else. Flag for review

Previous Question Next Question