Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Cutting large flexible cable

User: Wade M, Location: New York

Asked on: Monday, September 22, 2025 at 8:35 pm EDT
Answered on: Monday, September 22, 2025 at 9:12 pm EDT

Question: I've been reading this forum for years but finally took the jump to register because I have a very specific question I hope someone might help with.I'm going to be working soon with some Type W portable power cable. Five conductors at 2 AWG. Each conductor has 259 strands. The overall cable diameter is approximately 1.6 inches. I'm going to need to cut this cable.My shop has Greenlee battery cable cutters and I have a portaband. If this was THHN I wouldn't think twice and would just hit it with the portaband. But I've never taken a portaband to such a large and finely stranded cable, and I wonder how the Greenlee cutters would work on this cable. This cable is about $18/foot so I don't want to waste too much of it experimenting.My inclination is to use a 24 TPI portaband blade and run it fast but with very light pressure. If anyone has other ideas I'd love to hear them.Thanks.

Okay, this is a good question, and you're right to be thinking carefully about it given the cost of the cable. Here's a breakdown of your options, some suggestions, and things to consider

Understanding the Challenge
Fine Stranding

The high strand count (259) is the key here. It makes the cable very flexible, which is good for its application, but it also means the strands can easily fray, distort, and make a mess if not cut correctly.


Cable Construction

Type W cable typically has a tough, flexible jacket and individual conductor insulation. This layers can complicate cutting and require a clean cut to prevent damage to the insulation.

Comparing Cutting Methods



Greenlee Battery Cable Cutters (Hydraulic/Scissor-Type)



Pros

Designed specifically for cutting cable. Provide a clean, relatively undistorted cut when properly sized and maintained. Safer than a power tool, potentially.

Cons



Size Matters

Critical to ensure the cutters are rated for 2 AWG, 5-conductor Type W cable. Many cutters have specific size limits. Exceeding them can damage the cutters or produce a poor cut. Double check the tool's specs.


Potential for Distortion

If the cutters are dull or not properly aligned, they can crush/distort the cable instead of cutting cleanly. This can make stripping difficult and damage the strands.

Cost

Good quality battery-powered cutters can be expensive to replace.


Availability

You may not own an appropriate cutter and might need to borrow or rent one.

Portaband Saw



Pros

Fast and efficient. Can handle a variety of materials.

Cons



More Likely to Fray/Distort

The saw action can pull and distort the fine strands, especially if the blade isn't sharp or the speed/pressure is wrong.

Heat

Can generate heat that melts/deforms insulation.


Safety

Requires careful handling and eye protection.

Recommendations and Best Practices


Prioritize the Greenlee Cutters (But Check Them First)



Verify Compatibility



ABSOLUTELY ESSENTIAL

Confirm the cutters are rated for the size (2 AWG) and type (Type W, 5-conductor) of cable you are cutting. Look for markings on the tool itself or consult the manufacturer's specifications. Using the wrong size cutter is a recipe for disaster.

Inspect the Blades

Make sure the blades are sharp and in good condition. Dull blades will crush and deform the cable.

Test Cut (Ideally on Scrap)

If possible, sacrifice a short piece of cable to test the cutters before committing to the full cut. This will let you see how clean the cut is and if any adjustments are needed.


Proper Technique

Open the cutters fully, place the cable squarely between the blades, and apply steady, even pressure. Avoid twisting or jerking the cable.2.

If Using the Portaband (Only if Cutters Aren't Suitable)



Blade Selection

Your 24 TPI blade is a good start. A finer-tooth blade (e.g., 32 TPI)
might be even better at minimizing fraying, but it will cut slower.

Speed and Pressure

You're on the right track: High speed, very light pressure. Let the blade do the work. For this cable, a bi-metal blade is probably the best.

Clamping is Key

This is
crucial. Clamp the cable securely on BOTH sides of the cut line. Use V-blocks or padded clamps to avoid damaging the jacket. The goal is to prevent the cable from vibrating or moving during the cut.

Lubrication

A small amount of cutting fluid or even WD-40 can help keep the blade cool and reduce friction.

Cut Slowly and Deliberately

Don't force the blade. Let it cut at its own pace.


Deburr Immediately

After cutting, use a file or deburring tool to remove any sharp edges or burrs from the cable ends.

Consider Taping

Tightly wrap the cable with electrical tape
on both sides of the cut line before cutting. This can help hold the strands together and minimize fraying.

Take breaks

Pause cutting to check the blade and cable. Ensure nothing is over-heating.3.

Alternative Options (If Available)



Cable Shear (Bench-Mounted)

These are like large, heavy-duty scissor-type cutters that provide a very clean, square cut. If you have access to one, it's often the best option.


Rotary Cable Cutter

Some rotary cable cutters are designed for larger cables and can provide a clean, controlled cut.

Oscillating Multi-Tool (With Metal Cutting Blade)

Some people have had success using an oscillating multi-tool with a metal-cutting blade. Again, clamping and blade choice are critical.

Important Considerations



Safety

Wear appropriate safety glasses and gloves regardless of the cutting method you choose.

Strand Integrity

After cutting, inspect the strands of each conductor. If there are excessive frayed or damaged strands, you may need to trim back the cable slightly to get a clean connection.


Stripping

Be extra careful when stripping the insulation after cutting. Frayed strands can make stripping difficult and increase the risk of nicking the conductors.

Terminations

The type of termination (lugs, connectors, etc.) will also influence how important a clean cut is. Some terminations are more forgiving than others.

In summary:
Start with the Greenlee cutters if they are the correct size. Inspect and test them first. If you use the portaband, clamping is critical. Use a fine-tooth blade, light pressure, and consider taping the cable before cutting. Always prioritize safety and inspect the cable after cutting.Good luck! Let me know if you have any other questions. Flag for review

Previous Question Next Question