User: Jimmy7, Location: Boston, MA
Asked on: Wednesday, September 24, 2025 at 9:02 am EDT
Answered on: Wednesday, September 24, 2025 at 9:03 am EDT
Question: I have to replace an old bath fan light combo (Old work). It’s originally wire with two 14-2 from the bathrooms four gang switch box. At the fan a black from one 14-2 goes to the fan, and the black from the other cable goes to the light. From one 14-2 they spliced the white to the white of the fan, and from the other 14-2 they spliced the white of the white of the light. The four gang only has one feed. Is there any issue doing it this way? I typically run a 14-3 and call it a day.
You've described a common, albeit older, way of wiring a bath fan/light combo. While your typical method of using 14-3 is definitely cleaner and more straightforward, there's nothing inherently wrong with how it's currently wired, as long as it was done safely and correctly.Here's a breakdown of why your current setup works and potential issues to look out for
Why it Works (Potentially):
Separate Circuits
Using two 14-2 cables allows for completely separate circuits for the fan and the light. This is often done when you want the fan and light on different breakers, which can be advantageous for troubleshooting or energy management.
Single Feed at Switch
As long as the feed is correctly pigtailed to both switches for the fan and the light, that's not an issue. You're effectively distributing power to both circuits from a single source.
Neutral Sharing
The way you've described it, each device (fan and light) each gets its own dedicated neutral back to the panel.
Potential Issues to Check
Grounding
Crucially, ensure
both 14-2 cables have their bare copper ground wires properly connected. They must be connected to the grounding screw on the fan/light unit, and ideally pigtailed together and connected to the metal box (if applicable). Missing or improperly connected grounds are a major safety hazard.2. Overcurrent Protection
Make sure each circuit (fan and light) is protected by a
15-amp circuit breaker (assuming 14-gauge wire). If the breakers are larger than 15 amps, the wiring is not protected correctly.3. Wire Gauge
Double check that the wiring is actually 14 gauge. If it's 12 gauge, 20-amp breakers are appropriate. Using 14-gauge wire with a 20-amp breaker is a fire hazard.4.
Connections
Inspect all wire connections (especially those in the junction box in the bathroom) for looseness, corrosion, or poor workmanship. Use appropriate wire connectors (wire nuts, Wago connectors) and ensure they are properly tightened. Any loose connections will cause resistance and cause a fire.5.
Shared Neutral (If Not Correct)
If somehow both the light and the fan are sharing one neutral, this could cause overloading of the neutral wire. That is unsafe.
Why Your 14-3 Method is Preferable
Simplicity
One cable run simplifies wiring and reduces clutter.
Standard Practice
It's a more modern and widely accepted method.
Less Confusing
It's less prone to errors during installation or future modifications.
Recommendation
While you could technically reuse the existing wiring if it's in good condition and meets all safety requirements, your suggestion of running a 14-3 cable is strongly recommended. Here's why:
Safety
It eliminates potential issues with the existing wiring and ensures a safer, more reliable installation.
Best Practice
It's the preferred method and will be easier to understand and maintain in the future.
Resale Value
It's a small upgrade that can contribute to the overall quality and value of your home.
Wiring with 14-3 (If you choose this method)
Turn off the breaker! (Safety first).2. Run a new 14-3 cable from the four-gang switch box to the fan/light combo.
3. At the Fan/Light Unit
Connect the black wire of the 14-3 to the wire for the fan. Connect the red wire of the 14-3 to the wire for the light. Connect the white wire of the 14-3 to the neutral connection of the fan/light unit. Connect the bare copper ground wire to the grounding screw on the fan/light unit.4.
At the Four-Gang Switch Box
Connect the black wire of the 14-3 to one of the switch legs. Connect the red wire of the 14-3 to the other switch leg. Connect the white wire of the 14-3 to the neutral wire. Connect the bare copper ground wire to the grounding wire.
Important Note
If you're not comfortable working with electrical wiring,
hire a qualified electrician. Electricity is dangerous, and incorrect wiring can lead to fires, shocks, or even death. Always follow local electrical codes. Get permits if required by your municipality.In summary, while the existing setup may be technically acceptable if everything is done correctly, replacing it with a 14-3 cable is the safest and best practice. Prioritize safety and consult a professional if you're unsure. Flag for review