Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Clearance for a Emergency Shutoff?

User: Hobbyist, Location: Seattle

Asked on: Wednesday, September 24, 2025 at 5:58 pm EDT
Answered on: Wednesday, September 24, 2025 at 6:25 pm EDT

Question: I would like to run a conduit vertically next to an emergency shutoff for industrial equipment. The space I have available is tight so unless I can figure out another alignment I'll need to be within 30" of the work zone width. However, do I need to worry about the workzone for a switch? 110.26 says if the equipment is not likely to require maintenance I can ignore clearances.

You're right to be thinking about NEC 110.26 and the working clearances around electrical equipment. Here's a breakdown of how it applies to your situation, focusing on the emergency shutoff and your proposed conduit run

Understanding the Key Issue: Is the Emergency Shutoff Electrical Equipment Requiring Examination, Adjustment, Servicing, or Maintenance While Energized?
NEC 110.26 establishes minimum working clearances around electrical equipment. These clearances are intended to provide a safe working space for qualified persons to perform maintenance, examination, adjustment, or servicing. The Exception You Mentioned

You're correct that 110.26(A)(1)(a) states that these clearances aren't always required. Specifically, it says:_"Where the equipment is not likely to require examination, adjustment, servicing, or maintenance while energized, the clearances required in 110.26(A) shall not be required._"

Applying This to Your Emergency Shutoff


This is the crucial point: Is the emergency shutoff likely to require energized work? This requires a careful assessment. Here's how to think about it: Normal Operation

Emergency shutoffs are typically intended for
infrequent use.

Troubleshooting

Are repairs or checks of the shutoff likely? Are these likely to be done with the equipment energized?

Inspection

Are there requirements to regularly inspect the shutoff mechanism? If so, will this require energized checks?


Replacement

How often is the shutoff switch expected to be replaced? Is that work usually done live?

Making the Determination - Document Your Reasoning
Justification is Key

If you determine that energized work is
not likely, you must document your reasoning thoroughly. This is crucial for inspectors and future reference. Include details such as: The type of emergency shutoff (manufacturer, model, specifications) The environment (clean, dirty, etc.) The operating procedures for the equipment it controls The maintenance schedule Reasons why energized work is improbable

If Energized Work IS Likely

If you do determine that energized work is likely, you must comply with the full working clearance requirements of 110.26. The required clearances depend on voltage and other factors. Refer to Table 110.26(A)(1) for specific distances. The 30" width you mentioned refers to depth.

Potential Solutions When Clearance is Tight


If you determine that the working clearance is required and your space is tight, consider these options:1. Relocate the Shutoff

If possible, move the emergency shutoff to a location where clearances can be met.2.

Move the Conduit

As you initially alluded to, see if you can reroute the conduit to a different location that avoids encroaching on the working space.3.

Use a Smaller Conduit

Could you use a smaller conduit size or a different conduit type that would allow it to be closer to the shutoff and still meet code?4.

Engineering Judgement

You could seek an exception based on "engineering judgement". For example, if the only electrical componets are low voltage and physically protected, with zero risk of arc flash, then 110.26 clearance is not required. However, this typically requires approval from the AHJ (Authority Having Jurisdiction), like the local electrical inspector.

Important Considerations and Recommendations
Consult the AHJ

The final decision rests with the local electrical inspector (the AHJ - Authority Having Jurisdiction). It's always best to discuss your situation with them
before you proceed. They can provide valuable guidance and help you avoid costly rework.

Safety First

Even if energized work seems unlikely, always err on the side of caution. Electrical safety is paramount.

Future Considerations

Think about potential future changes. Could the equipment or operating procedures change in a way that would make energized work more likely?


Other Codes and Standards

Be aware that other codes or standards (e.g., OSHA, internal company policies) may have additional requirements for safety around electrical equipment.

Lockout/Tagout (LOTO)

While you're focusing on energized work, remember that proper Lockout/Tagout procedures are essential whenever electrical work is performed.

In Summary


The key question is whether the emergency shutoff is "likely to require examination, adjustment, servicing, or maintenance while energized." If not, the working clearances of 110.26 may not apply, but you
must* document your reasoning. When in doubt, consult with the AHJ and prioritize safety. If energised maintenance is likely, it is your best bet to find a different path for the conduit or a new location for the shutoff. Flag for review

Previous Question Next Question