Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Fire Alarm Conduit

User: Alwayslearningelec, Location: NJ

Asked on: Friday, September 26, 2025 at 2:59 pm EDT
Answered on: Sunday, September 28, 2025 at 3:29 am EDT

Question: Is there anyway you could( or would) have a common conduit down the wall for the devices back to back?

Yes, you absolutely could (and often should) use a common conduit down the wall for back-to-back devices. Here's a breakdown of why, when, and how

Why a Common Conduit is a Good Idea:
Simplifies Wiring

Reduces the number of holes you need to drill in the wall and makes pulling wires easier.


Neater Appearance

A single, well-placed conduit is generally more visually appealing than multiple individual ones.

Future-Proofing

A larger conduit can accommodate future wiring upgrades or additions without requiring new wall penetrations.


Code Compliance (Potentially)

In some cases, local electrical codes require common raceways or conduits for multiple circuits serving different devices.

Considerations and Planning


Electrical Code



Always check your local electrical code.
It will dictate requirements for conduit type, sizing, fill capacity (how many wires you can put in a conduit), and segregation of different types of wiring. National Electrical Code (NEC) and regional/local amendments will be the governing standards in the US. Similar codes apply in other countries. Voltage

Determine if the circuits are high voltage (120V+) or low voltage (Cat6, HDMI, etc). Some codes may restrict sharing a conduit between high and low voltage.2.

What Devices are Back-to-Back?
This is crucial for wire types and sizes:
Outlets

Standard 120V or 240V outlets.

Switches

For lighting.


Light Fixtures

Wiring for the light itself.

Data/Network (Cat6, Ethernet)

For internet connectivity.


AV (HDMI, Coax)

For television, audio, and video.

Thermostats/Smart Home Devices

Low-voltage wiring for sensors and control.3.

Conduit Type



EMT (Electrical Metallic Tubing)

Thin-walled steel conduit. Common, relatively inexpensive, and easy to work with. Often preferred for residential and commercial.

PVC (Polyvinyl Chloride)

Plastic conduit. Resistant to corrosion, but can be more difficult to bend and may have limitations on where it can be used (e.g., not allowed in some plenum spaces).


Flexible Metal Conduit (FMC)

Flexible metal "armor." Easier to route around obstacles but offers less physical protection.

Liquidtight Flexible Metal Conduit (LFMC)

Similar to FMC but with a waterproof jacket. Used in damp or wet locations.4.

Conduit Size



Calculate the total cross-sectional area of all the wires you plan to run.
Consult the electrical code for the maximum fill percentage allowed for the conduit type. The code specifies how much of the conduit's internal space can be occupied by wires. Usually a percentage (40% is common for new work). Choose a conduit size that meets or exceeds the required capacity. Err on the side of slightly larger, as it's easier to pull wires through a larger conduit. Use online conduit fill calculators

Many websites offer tools to help you calculate the correct conduit size based on wire types and quantity.5.

Box Fill



Consider the volume of the boxes where the wires terminate.
Each wire, device (outlet, switch, etc.), and fitting (e.g., wire connectors) contributes to the "box fill" calculation. Ensure that the boxes are large enough to accommodate all the wires and devices without exceeding the maximum fill capacity. Overfilled boxes are a fire hazard.6. Wire Types



NM-B (Non-Metallic Sheathed Cable)

Common for residential wiring inside walls. Often called "Romex." Generally, NM-B cable should not be run inside conduits for its entire length, but specific short sections are sometimes permissible. Check your local code. It can be used in a conduit for protection near the device box, but the entire run can't be in conduit unless the conduit is very large.

THHN/THWN

Individual insulated wires, often used inside conduits. THHN is dry location rated; THWN is wet location rated. These are a good choice for pulling through conduit.


Low-Voltage Cables

Cat6, HDMI, Coax. These can be run separately or in a different compartment/conduit from power wires in many jurisdictions.

Always use the correct wire type for the application and environment.
7. Grounding



Proper grounding is essential for safety.
Ensure that the conduit is properly grounded. Metal conduit typically serves as the grounding conductor. Bond the boxes to the grounding system. If using PVC conduit, you must run a separate grounding wire.Example Scenario

Let's say you have a wall with an outlet on one side and a network jack on the other, directly back-to-back. You want to run wiring for both through a single conduit.1.

Code Check

Verify local code requirements for conduit type, fill, and low-voltage/high-voltage separation.2.

Wiring Needs

Outlet: 120V power (likely two 12 AWG or 14 AWG wires + ground) Network Jack: Cat6 cable3.

Conduit Choice

Based on code and space, 3/4" EMT conduit might be suitable.4.

Wire Types

THHN/THWN for the power wires.5.

Separation (if required)

You might run the Cat6 cable outside the conduit but securely attached to it. Alternatively, you could use a conduit with a divider to physically separate the power and data cables.6.

Boxes

Choose appropriate boxes for the outlet and network jack, ensuring sufficient box fill capacity.

Steps for Installation (General - Consult a Professional)


Turn off the power to the circuit you're working on!
2. Locate Studs

Find the wall studs to avoid cutting through them.3.

Cut Holes

Cut appropriately sized holes for the boxes.4.

Install Boxes

Secure the boxes to the studs.5.

Run Conduit

Measure and cut the conduit to the appropriate length. Bend the conduit (if necessary) using a conduit bender. Attach the conduit to the boxes using appropriate fittings (connectors).6.

Pull Wires

Use a fish tape to pull the wires through the conduit. Leave enough wire at each box for connections.7.

Make Connections

Connect the wires to the devices (outlet, network jack) according to the manufacturer's instructions. Ensure all connections are secure.8.

Grounding

Ensure proper grounding.9.

Test

Turn the power back on and test the devices to ensure they are working correctly.

Important Considerations & Safety



Electrical work can be dangerous. If you are not comfortable or experienced working with electricity, hire a qualified electrician.
Always double-check your work and follow all safety precautions. Obtain any necessary permits before starting the work. Pull a permit and have the installation inspected by a qualified electrical inspector.

In summary, using a common conduit for back-to-back devices is often a good idea, but proper planning, code compliance, and safety are paramount. Consult a qualified electrician if you have any doubts. Flag for review

Previous Question Next Question