Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Voltage drop

User: stretch12, Location: taxachusetts

Asked on: Saturday, September 27, 2025 at 12:36 pm EDT
Answered on: Sunday, September 28, 2025 at 3:31 am EDT

Question: I’m trying to figure voltage drop on a resi service 120/240 single phase . Distance is approximately 2k ft from xformer to residence. Figuring on al conductors, the south wire app is showing ridiculous amount of parallel conduits. I haven’t done one of these calculations in like 15 yrs. And am having the largest brainfart of my life trying to get started.Any assistance or insight, very much appreciated.Chris

Okay, let's break down this long-distance residential service voltage drop calculation and get you unstuck. It's definitely a challenging situation with that 2000ft distance!1. Gather Your Information



Voltage

120/240V single-phase


Distance (One-Way)

2000 ft (This is critical. All VD calculations use the one-way distance of the conductor run.)

Material

Aluminum (Al)


Allowable Voltage Drop

This is KEY. The NEC has recommendations, but the actual allowable VD might be dictated by local codes or the utility company. Generally, you want to aim for:

3% Maximum Voltage Drop for Branch Circuits

While this is technically for branch circuits, it's a good target to aim for overall. 3% of 240V is 7.2V.


5% Maximum Voltage Drop Combined for Feeder + Branch Circuits

Consider that some of this drop will occur in the house wiring. So, if possible, keep the service drop lower than 3% to give the house wiring some wiggle room.

Load (Amps)

This is the hardest and most critical part! You
must accurately estimate the expected maximum load the house will draw.

NEC Article 220 Load Calculation

The NEC provides methods for calculating the service load based on the dwelling's square footage, appliance load (ranges, dryers, A/C, etc.), and other factors. This is essential. Don't guess. A shortcut would be the optional calculation of 220.82.

Future Growth

Always factor in some extra capacity for future additions or changes to the house. Underestimating now will cause problems later. 125% is a reasonable start.

Diversity

Remember that not all appliances run at full load simultaneously. NEC load calculations account for this.

Transformer Impedance

Ideally, get this from the utility company. It affects the voltage drop at the service entrance. If you can't get it from the utility, you will have to ignore it (which is a conservative approach).

2. Initial Sizing & Voltage Drop Calculation



Start with a Reasonable Size

Based on experience, and before doing the voltage drop calculation, you'll need to estimate what conductor size is likely necessary based on the load you calculated in step 1. Remember that at 2000 feet you're almost certainly going to need parallel conductors.

Southwire App (or other VD Calculator)

This is where the Southwire app comes in.


Input the Data

Enter the following information: Voltage (240V) Amps (Calculated load - See Step 1) Distance (2000 ft) Conductor Material (Aluminum) Conductor Size (Start with your estimate - something substantial, like 4/0 or larger per conductor in parallel) Number of Conductors per Phase (Start with 2 or 3) Conduit Material (PVC or Aluminum - this affects temperature rating and ampacity) Ambient Temperature (Important for ampacity derating)

Check Ampacity

Make sure the ampacity of your conductor is
higher than the calculated load. You may need to adjust the size or increase the number of parallel conductors if the ampacity is too low, taking into account ambient temperature.

Check Voltage Drop

Look at the voltage drop percentage. If it's above your allowable percentage (e.g., 3%), you need to: Increase the conductor size. Increase the number of parallel conductors.

3. Addressing the "Ridiculous" Parallel Conduits

This is likely what's happening. At 2000 feet, you're fighting a significant battle with voltage drop and conductor ampacity, and aluminum has higher resistance than copper. Here's how to deal with it:

Parallel Conductors are Likely Necessary

Accept that you'll almost certainly need parallel runs. It's the nature of the beast with that distance.


Minimize Runs

Consider cost-benefit analysis. Going with more parallel runs of smaller conductors will require more conduit. Fewer parallel runs of very large conductors will be more expensive per conductor. Find the right balance to minimize cost.

Bonding and Grounding

Proper grounding and bonding are
essential with parallel conductors. NEC Article 250 covers this. Pay close attention to grounding electrode conductor (GEC) sizing and bonding jumper requirements.

Raceway Type

Ensure the chosen raceway type (PVC, aluminum conduit, etc.) is suitable for the environment and complies with local codes. Aluminum conduit can help mitigate voltage drop slightly.

4. Working with the Utility Company



Contact the Utility

This is
critical.

Transformer Information

Get the transformer size and impedance.

Point of Connection

Confirm the exact point of connection on the transformer.


Voltage Regulation

Inquire about the utility's voltage regulation policies.

Special Requirements

Find out if they have any specific requirements for long service runs like this (e.g., voltage drop limits, grounding requirements). They may even need to upgrade the transformer.

5. Example (Simplified)

Let's assume after doing a load calculation per NEC 220, you determine a total service load of 200A.1.

Start with 4/0 Al

Try running two parallel runs of 4/0 Aluminum.2.

Southwire Calculation

Input 240V, 200A, 2000ft, 4/0 Al, 2 conductors per phase, and conduit information.3.

Ampacity Check

4/0 Al has an ampacity of around 230A in ideal conditions. With two in parallel, that's 460A, which is
more than your 200A load, so ampacity is OK (assuming no severe derating).4.

Voltage Drop Check

The Southwire app might show something like 8% voltage drop (this is just an example).5.

Increase Conductors

Since 8% is too high, try three parallel runs of 4/0. Recalculate.
6.


Iterate

Continue adjusting the number of conductors or the conductor size until you get a voltage drop within your acceptable range (e.g., 3%).

Key Considerations



Cost

Factor in the cost of the conductors, conduit, fittings, labor, and any potential transformer upgrades.

Accessibility

Ensure the conduit runs are accessible for future maintenance or repairs.


Inspection

Be prepared for a thorough inspection. Have your calculations and documentation ready.

Important Notes



This is a simplified explanation.
Complex installations may require more detailed calculations and considerations. Consult with a qualified electrical engineer or experienced electrician before proceeding with the installation. This is not a DIY project. Always comply with the NEC and local electrical codes. Double-check all calculations. Errors can be costly and dangerous.Let me know if you want me to elaborate on any specific aspect of this process. Good luck! Flag for review

Previous Question Next Question