User: steve61, Location: Nebraska
Asked on: Monday, September 29, 2025 at 1:14 pm EDT
Answered on: Monday, September 29, 2025 at 1:14 pm EDT
Question: I have a 100 amp single phase panel fed with a pair of # 2 feeders and a # 2 neutral wire. The internals of the existing panel are broken and the breakers keep falling out of place. I have a spare 150 amp panel that I would like to replace the existing panel with. Since there is very little load on the existing panel, just several 120 volt receptacles, can I install the 150 amp panel using the # 2 feeders ? I have a 100 amp and a 125 amp two pole breaker to feed the new panel with. Thanks for any info.
Okay, let's break down the situation and address your question.
Understanding the Situation Existing Setup
You have a 100-amp single-phase panel fed by #2 AWG conductors and a #2 AWG neutral. This is a standard configuration for a 100-amp service.
Problem
The existing panel is faulty and breakers are not staying in place.
Proposed Solution
Replace the 100-amp panel with a spare 150-amp panel that you have on hand.
Question
Can you use the existing #2 AWG conductors to feed the new 150-amp panel, and which breaker size to use (100A or 125A)?
Analysis and Answer
Yes, you can use the existing #2 AWG conductors to feed the 150-amp panel if you protect them with a 100 amp breaker.Here's the reasoning based on the National Electrical Code (NEC) and general electrical principles:1. Conductor Ampacity
According to NEC Table 310.16 (and similar tables), #2 AWG copper conductors (which I am assuming yours are), typically have an ampacity of 95 amps at 75°C (the typical termination temperature rating for breakers and panels). Some tables allow for a 115 amp rating but this is generally limited to specific applications.
2.
Overcurrent Protection
The purpose of a circuit breaker (or fuse) is to protect the conductors from overcurrent. The breaker should be sized no larger than the ampacity of the conductors. Since your #2 conductors are rated for 95 amps, you cannot use a 125 amp breaker to feed the new panel.3.
Panel Rating vs. Feeder Rating
The panel's rating (150 amps in your case) is the maximum current the panel's busbars and components can handle. You don't have to use a breaker that matches the panel's rating. The breaker protects the conductors feeding the panel.4.
Increasing Panel Size
Using a larger panel (150 amps instead of 100 amps) does not require you to upgrade the feeder conductors as long as the feeder breaker protects them accordingly. The larger panel simply gives you more breaker slots and more capacity within the panel for future circuits if you were to upgrade the feeder conductors in the future.5.
Neutral Conductor
The #2 AWG neutral is also adequate for a 100-amp single-phase service.
Recommendations Install the 150-amp panel. This will give you more breaker spaces for future expansion if needed. Use a 100-amp two-pole breaker to feed the 150-amp panel. This will protect the #2 AWG conductors according to code. Connections
Ensure all connections are clean, tight, and properly torqued according to the panel manufacturer's specifications. Use an anti-oxidant compound on aluminum connections.
Grounding
Properly ground the new panel according to the NEC. This includes connecting the grounding electrode conductor (typically to a grounding rod or water pipe) to the grounding bus in the panel and bonding the neutral bus to the panel enclosure (if it's a service panel).
Labeling
Clearly label the new panel and all circuits.
Professional Inspection
It is highly recommended to have a licensed electrician inspect the installation to ensure it meets all applicable codes and is safe.
Important Safety Considerations Work De-energized
Always turn off the main breaker at the source (e.g., the meter base) before working on any electrical panel.
Test for Voltage
Use a reliable voltage tester to confirm that the power is off before touching any wires.
Personal Protective Equipment (PPE)
Wear appropriate PPE, including safety glasses and insulated gloves.
If you are not comfortable or experienced working with electrical systems, hire a qualified electrician. Electrical work can be dangerous and can result in serious injury or death if not done properly. Also, electrical work is subject to inspections and permits so hire an electrician to be sure the work is done to code.
Disclaimer: I am an AI chatbot and cannot provide definitive electrical advice. This information is for general guidance only. Always consult with a qualified and licensed electrician for any electrical work. Flag for review