Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: A to D converters - How to wire timing & control logic

User: Carultch, Location: Massachusetts

Asked on: Tuesday, September 30, 2025 at 12:54 am EDT
Answered on: Tuesday, September 30, 2025 at 1:00 am EDT

Question: I'm working with this product, and I'm trying to make sense of how to wire the following pins:https://www.digikey.com/en/products/detail/texas-instruments/TLC0820ACN/371711

Okay, I've reviewed the datasheet for the Texas Instruments TLC0820ACN Analog-to-Digital Converter (ADC). Here's a breakdown of how to wire its pins, focusing on typical usage and considerations

Pin List and Function

Refer to the datasheet for the specific pinout diagram. However, here's a general description of each pin and how you'd typically connect it:| Pin # | Name | Description | Typical Wiring | Considerations

-------|------|-------------|----------------|----------------
1 | IN+ | Positive Analog Input | Connect to the signal you want to convert to digital. | Voltage must be within the valid input range of the ADC (usually related to VREF/2). Consider input impedance of the ADC and the source impedance of your signal. Use a buffer amplifier if necessary.
2 | IN- | Negative Analog Input | Typically grounded for single-ended measurements, or connected to a reference voltage. | For differential measurements, use this to cancel out common-mode noise. Important for high-precision applications. Must be within the valid input range relative to VREF/2.
3 | VREF | Reference Voltage | Connect to a stable, precise voltage source. | This voltage determines the full-scale range of the ADC. The ADC's output will scale proportionally to VIN relative to VREF. CRITICAL

Choose a reference voltage with low noise and good temperature stability. Bypass with a capacitor close to the pin.
4 | GND | Ground | Connect to the system ground. |
CRITICAL
Star grounding is highly recommended to minimize ground loops and noise. Use a solid ground plane on your PCB.
5 | DOUT | Data Output | Connect to a microcontroller or digital logic for reading the converted data. | Data is parallel, typically 8-bit. Check the timing diagrams in the datasheet to understand when the data is valid.
6 | CLK | Clock Input | Connect to a clock signal. | The clock frequency determines the conversion rate of the ADC. Check the datasheet for the allowed clock frequency range.
7 | EOC | End of Conversion | Connect to a microcontroller interrupt pin or polling input. | This signal indicates when a new conversion is complete and the data is ready to be read. || 8 | VCC | Positive Power Supply | Connect to the appropriate power supply voltage (typically +5V). | Bypass with a capacitor (e.g., 0.1uF ceramic) close to the pin. Check the datasheet for the allowable voltage range. |


Example Wiring Scenario (Single-Ended Measurement)


Let's say you want to measure a voltage from 0V to 2.5V using a +5V supply.
1. VCC

Connect to +5V, bypass with a 0.1uF ceramic capacitor close to the pin.
2.


GND

Connect to ground.3.

IN+

Connect to the voltage you want to measure. If the source impedance of your signal is high (e.g., > 1kΩ), consider using an op-amp buffer before connecting it to IN+.4.

IN-

Connect to ground.5.

VREF

Connect to a precise 2.5V reference voltage source. Bypass with a 0.1uF ceramic capacitor close to the pin.
6.


CLK

Connect to a clock signal (e.g., from a microcontroller or a 555 timer). Choose a frequency within the ADC's specified range.7.

DOUT

Connect the 8 data output pins to the corresponding input pins of your microcontroller or digital logic.8.

EOC

Connect to an interrupt pin or a polling input on your microcontroller.

Important Considerations and Best Practices
Decoupling Capacitors

Bypass VCC and VREF with 0.1uF ceramic capacitors placed
as close as possible to the pins. This helps filter out noise from the power supply.

Grounding

Use a star grounding configuration. Connect all ground connections to a single point to minimize ground loops. A ground plane on your PCB is highly recommended.

Reference Voltage

The accuracy of the ADC depends heavily on the accuracy and stability of the reference voltage. Choose a reference with low noise, good temperature coefficient, and good initial accuracy. Consider using a dedicated voltage reference IC.


Input Signal Conditioning

The input signal may need to be scaled or buffered before being applied to the ADC. Use an op-amp buffer if the source impedance of your signal is too high. Filter your input signal.

Timing

Carefully review the timing diagrams in the datasheet. You need to provide the correct clock frequency and wait for the EOC signal to indicate that the conversion is complete before reading the data from the DOUT pins.


Resolution

This is an 8-bit ADC, meaning it will divide the input range (0 to VREF) into 256 discrete steps. Each step will have a size of VREF / 256.

Layout

Keep analog and digital signals separate on your PCB. Minimize the length of traces carrying analog signals.


Differential vs. Single-Ended

If you are measuring a small signal in a noisy environment, consider using differential mode. Connect the positive and negative signal leads to IN+ and IN-, respectively.

Input Voltage Range

Ensure that the input voltage on IN+ and IN- is within the ADC's specified input voltage range. Exceeding the range can damage the ADC.

Troubleshooting Tips
No Output

Check your power supply voltage, ground connections, clock signal, and reference voltage.

Inaccurate Output

Check the accuracy of your reference voltage, the stability of your power supply, and the impedance of your input signal.


Noisy Output

Check your grounding, decoupling capacitors, and the noise level of your reference voltage.

Data Sheet is Key:
Always double-check the datasheet for the exact pinout, specifications, and timing requirements.To help me tailor the information better to your needs, please provide more information about your specific application, such as: What are you measuring? (e.g., voltage, current, temperature) What is the expected range of the input signal? What is the source impedance of the input signal? What are you using to process the digital output from the ADC (e.g., microcontroller, FPGA)? What is your desired conversion rate?With more details, I can provide more specific wiring recommendations and troubleshooting advice. Flag for review

Previous Question Next Question