Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Fire Alarm Question

User: Alwayslearningelec, Location: NJ

Asked on: Tuesday, September 30, 2025 at 7:48 am EDT
Answered on: Tuesday, September 30, 2025 at 7:49 am EDT

Question: If you are renovating a space and they show (4) existing fire alarm devices( there are many more new devices being installed in the sapce) in the space to be demolished and are in same exact location as new but you need to keep the system up and running as the loop these existing devices are on feed adjacent spaces how would you handle keeping the system active at all time? Thanks

This is a common challenge in renovations, and requires careful planning and coordination to maintain fire alarm system integrity. Here's a breakdown of how to handle this situation

1. Planning and Coordination (Most Important):
Contact the Fire Alarm Vendor/Contractor IMMEDIATELY

This is not a DIY situation. You need a qualified fire alarm technician experienced with the specific system. Their expertise is crucial for safe and compliant solutions.


Review Approved Design/Contract

Confirm the design is approved and is being followed.

Inform Authority Having Jurisdiction (AHJ)

Depending on your local codes and regulations, you may need to inform the fire marshal or other relevant authorities about the renovation and the plan for maintaining fire alarm functionality. They may have specific requirements.


Circuit Identification

Clearly identify the precise circuit loop that includes the devices being removed and the adjacent spaces they protect.

Communication

Maintain clear communication between the demolition crew, electrical contractor, and fire alarm technician. Everyone needs to understand the critical nature of the fire alarm system.

2. Temporary Wiring and Relocation (The Primary Method)



Temporary Wiring Run

Before demolition begins, the fire alarm technician will run temporary wiring to the existing devices that are being removed. This will be done with the proper gauge wire, conduit (if required by code), and connections to ensure signal integrity. The temporary wiring must be run in a safe and secure manner that does not create trip hazards or interfere with the renovation work.

Temporary Mounting/Relocation (Within the Space)

The goal here is to relocate the
existing devices while keeping them connected to the existing loop. Ideally, relocate the device a short distance within the room, away from the demolition area, but still within code-compliant coverage. This could involve temporarily mounting them to a nearby wall or ceiling that is not being demolished.

Device Testing

After relocation and temporary wiring,
immediately test each device to ensure it's functioning properly and communicating with the panel. Document the test results.

Monitor the System

As the adjacent area is still active the system should be monitored at all times.

3. Careful Removal and Reinstallation



Careful Removal

The demolition crew needs to be extremely careful when removing the old wiring and mounting hardware. They must
not damage the temporary wiring or any other part of the fire alarm system.

Device Replacement

After all demolition/installation has been completed the existing devices should be removed.

Final Testing

After the new devices have been installed and wired into place by the fire alarm contractor the entire circuit must be tested to ensure they are working correctly and are communicating to the panel.

4. Important Considerations and Potential Challenges



Code Compliance

All temporary and permanent wiring and device placement must comply with applicable fire codes (NFPA 72 in the US). The fire alarm technician must be familiar with these codes.

Device Compatibility

Ensure the new devices are fully compatible with the existing fire alarm panel and loop. This is typically the responsibility of the fire alarm contractor.


Power Supply

The existing power supply for the fire alarm system must be adequate to support both the existing and new devices. The fire alarm technician will verify this.

Supervision

The fire alarm system should be continuously supervised by a monitoring company, if required by code, during the renovation. This allows for immediate response in case of an alarm or fault.


Documentation

Maintain detailed records of all temporary wiring, device relocations, testing, and inspections. This documentation will be valuable for future maintenance and inspections.

Dust and Debris

Demolition work can generate a lot of dust and debris, which can interfere with the operation of smoke detectors. Protect the existing devices as much as possible from dust and debris. Consider using temporary covers.


False Alarms

Renovations can sometimes trigger false alarms. Be prepared to respond quickly and to identify and correct the cause of the false alarm.

Cost

Maintaining fire alarm functionality during renovations can add to the cost. Be sure to factor this into the project budget.


Alternative

If the devices being demolished are part of a larger loop that also serves an adjacent area, and temporary relocation is not feasible, you might consider a complete system shutdown for the shortest possible duration. This requires VERY careful planning, coordination, and approval from the AHJ. It also typically requires a fire watch. This is rarely the preferred solution.

In summary, the key to success is careful planning, coordination, and the expertise of a qualified fire alarm technician. Don't cut corners on this – the safety of the building occupants depends on it.
Flag for review

Previous Question Next Question