Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Grounding for multiple raceways and cable tray.

User: derekmman, Location: Memphis, TN

Asked on: Tuesday, September 30, 2025 at 3:56 pm EDT
Answered on: Tuesday, September 30, 2025 at 3:58 pm EDT

Question: Hello everyone,I have a scenario on a project that we can't seem to agree on and would like your input.I have a 480 volt, 1140amp circuit that is coming out of our MDP that is feeding a load a few hundred feet away.It is being paralleled 3 times with 500MCM tray cable. It goes from 3 conduits, one per parallel, to cable tray back the to 3 conduits at the load end.The question is, do we have run three separate 3/0 grounds or could we run one 3/0 in the tray and tap it at the ends for the conduit?

Okay, this is a common point of debate, and it's important to get it right for safety and code compliance. Here's a breakdown of the issues and my opinion, along with the reasoning

The Core Issue: Grounding and Fault Current Path

The purpose of an equipment grounding conductor (EGC) is to provide a low-impedance path for fault current back to the source. This is critical for quickly tripping the overcurrent protective device (OCPD) in the event of a ground fault, which minimizes shock hazards and equipment damage.

Why Splitting the Ground is Generally Required



Inductive Reactance

In AC circuits, conductors generate a magnetic field around them. When current changes rapidly (as during a fault), this magnetic field induces a voltage that opposes the change in current. This opposition is called inductive reactance.


The Problem

If you run a single 3/0 ground some distance away from the phase conductors, the inductive reactance can significantly increase the impedance of the ground fault path. This impedance reduces the fault current, potentially preventing the OCPD from tripping quickly or at all.

Code Compliance (NEC 250.122(C))

The NEC emphasizes the importance of running the grounding conductor in the same raceway or cable as the phase conductors to minimize inductive reactance.


Fault Current Distribution

When you parallel conductors, the fault current will divide between them proportionally to their impedance. If you have one grounding conductor and multiple ungrounded (phase) conductors, the ground fault current will not be properly distributed. This can overload the single grounding conductor and further increase impedance.

Arguments for a Single Tapped Ground (and why they are generally insufficient)



Cost Savings

Obviously, using one ground conductor saves on material and labor.


Perceived Redundancy

Some might argue that a single 3/0 ground is "enough" to handle the fault current.

Why the Single Tapped Ground is Likely NOT Compliant and UNSAFE


NEC 250.122(C) clearly states

"Where conductors are installed in parallel in multiple raceways or cables, as permitted in 310.10(H), the equipment grounding conductors shall also be installed in parallel." This is exactly your situation. The wording is pretty unambiguous. Each parallel set of conductors must have its own grounding conductor.2.

Fault Current Considerations

A 3/0 copper conductor may seem like it has the ampacity to handle the fault current. However, ampacity is about heat dissipation under normal load conditions. During a ground fault, the instantaneous current can be
much higher than the normal load, and the speed of clearing the fault is paramount. You need the lowest possible impedance.3.

Code Rationale

The parallel grounding rule isn't just arbitrary. It's based on years of experience and testing showing that it's necessary for reliable fault clearing.

Your Specific Situation



Paralleled 500 MCM Conductors

These are high-capacity conductors, which means the potential fault current is also high. A faster trip is more essential for larger services and feeders.

"A Few Hundred Feet"

The longer the run, the more significant the inductive reactance becomes.

The Verdict

You almost certainly

MUST
run three separate 3/0 grounding conductors, one in each conduit/cable tray pathway.

How to Do It Right


Run (3) 3/0 Copper Grounds

One in each of the three conduit runs and continuous along the cable tray run.2.

Termination

Properly terminate the grounding conductors at the MDP and at the load end. Use appropriate lugs and torque to specification.3.

Inspection

Make sure this installation is inspected to verify compliance with NEC 250.122(C).

Important Considerations



Engineering Judgment

While the NEC is very specific here, always involve a qualified electrical engineer in the design, especially with large systems like this. They can perform fault current calculations to verify the adequacy of the grounding system.

Local Amendments

Check for any local amendments to the NEC that might be more stringent.


Cable Tray Bonding

Cable tray sections MUST be properly bonded together to provide a continuous grounding path. Use listed bonding jumpers where sections are not automatically bonded by bolted connections.*

Aluminum vs. Copper

My recommendation is based on using copper. If you're considering aluminum grounding conductors, the size will need to be increased to achieve equivalent performance, and the termination methods will be different.

In Summary:


While saving money on the ground wire might seem appealing, it is not worth the risk of creating a potentially dangerous situation. Follow the code, prioritize safety, and consult with a qualified engineer. It's simply not worth the potential consequences of a delayed or failed fault clearing. Flag for review

Previous Question Next Question