User: Alwayslearningelec, Location: NJ
Asked on: Friday, October 3, 2025 at 10:43 am EDT
Answered on: Friday, October 3, 2025 at 10:44 am EDT
Question: Of the main is staying would you remove and reinstall these (2) 800A and (1) 400A breaker while gear is live or is that way too dangerous? ThanksView attachment 2579899
Removing and Reinstalling Breakers in Live Gear: A Highly Dangerous Practice
Based on the information provided and standard safety practices, removing and reinstalling 800A and 400A breakers while the gear is live is extremely dangerous and not recommended.
Reasons Why This is So Risky
Arc Flash Hazard
Working on live equipment, especially with high currents like 800A and 400A, carries a significant risk of arc flash. An arc flash is an explosive release of energy due to an electrical fault. It can cause severe burns, blindness, hearing loss, and even death. The severity of an arc flash is directly related to the available fault current and the clearing time of the overcurrent protection.
Electrocution Risk
Direct contact with live conductors or components poses a serious electrocution hazard. Even brief contact can be fatal.
Equipment Damage
Improper handling or installation of breakers while the gear is live can damage the breakers, the busbars, or other components. This can lead to equipment failure and further safety hazards.
Human Error
Working under stress, fatigue, or with distractions increases the likelihood of human error, which can have catastrophic consequences in a live electrical environment.
Compliance
Most electrical codes and safety standards (like OSHA in the US and similar regulations elsewhere) strictly prohibit working on live equipment unless it is absolutely unavoidable and specific procedures and PPE are in place.
Mechanical Risks
The act of removing and installing a breaker can introduce metallic objects and the potential to accidentally short phases together.
What to Do Instead (Recommended Safe Procedure)
De-energize the Equipment
The safest approach is to de-energize the gear completely before removing and reinstalling the breakers. This typically involves: Properly planning and coordinating the outage. Switching off the upstream power source (main breaker, transformer, etc.). Locking out and tagging out (LOTO) the disconnecting means to prevent accidental re-energization. Verifying that the equipment is de-energized using a properly rated voltage tester.2.
If De-energizing is Absolutely Impossible (Very Rare)
If, and only if, there is a compelling reason why the equipment cannot be de-energized, the following precautions MUST be taken:
Qualified Personnel
Only highly qualified and experienced electricians with specific training in working on live equipment should perform the work.
Arc Flash Risk Assessment
Conduct a thorough arc flash risk assessment to determine the potential hazard level and the required PPE.
Appropriate PPE
Wear full arc flash-rated PPE, including a suit, gloves, face shield, and hearing protection.
Insulated Tools
Use properly insulated tools that are rated for the voltage being worked on.
Procedures
Follow detailed written procedures for removing and reinstalling the breakers.
Safety Observer
Have a safety observer present to monitor the work and provide assistance if needed.
Approach Boundaries
Maintain proper approach boundaries to energized parts.
Environmental Conditions
Ensure proper lighting and a clean, dry working environment.
Important Considerations
Breaker Condition
Before reinstalling the breakers, inspect them thoroughly for any signs of damage or wear. If a breaker is faulty, it should be replaced, not reinstalled.
Torque
Ensure that all connections are properly torqued to the manufacturer's specifications.*
Testing
After reinstalling the breakers, perform functional testing to verify that they are operating correctly.
In Summary
Working on live electrical equipment is inherently dangerous. The risks associated with removing and reinstalling high-amp breakers while the gear is live are significant.
Always prioritize safety and de-energize the equipment whenever possible. If live work is unavoidable, take extreme precautions and ensure that all applicable safety procedures are followed.
Disclaimer: This information is for general guidance only and should not be considered a substitute for professional advice. Always consult with a qualified electrician and refer to applicable codes and standards before performing any electrical work. Flag for review