Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Ground Mount Solar Rack Grounding/Bonding

User: MChav841, Location: Blythewood, SC

Asked on: Saturday, October 4, 2025 at 3:20 pm EDT
Answered on: Saturday, October 4, 2025 at 4:52 pm EDT

Question: I will be ground mounting 4 rigid solar panels to an IntegraRack solar rack and using water tote tanks to anchor the rack. The panels will be wired in series and connected to a PV disconnect. The PV wire will be run from the disconnect and underground (approx. 90 feet) through rigid metal conduit to the garage. I will be using the panels to charge an Anker Solix F3800 Plus, which will be used for backup power via a 10-circuit 30amp manual transfer switch. What are the grounding and bonding requirements in this scenario?

Okay, let's break down the grounding and bonding requirements for your solar panel setup. This is not a replacement for a qualified electrician who is familiar with local codes. Always consult with a qualified electrician and follow all applicable local and national codes (primarily the National Electrical Code (NEC) in the US).

Disclaimer

I am an AI assistant and cannot provide electrical advice. This information is for general educational purposes only. You are responsible for the safety and code compliance of your installation. Improper grounding and bonding can lead to equipment damage, fire hazards, and electric shock.

General Grounding and Bonding Principles


The fundamental goals of grounding and bonding in a PV system are: Safety

To protect people from electrical shock.


Equipment Protection

To protect the solar panels, inverter/charger, and other components from damage due to ground faults (unintended contact between a live conductor and ground).

Lightning Protection

While grounding doesn't
prevent lightning strikes, it provides a path for lightning energy to dissipate, reducing the risk of damage.

Code Compliance

To meet the requirements of the NEC (or your local electrical code).

Specific Grounding and Bonding Requirements for Your System


Here's a breakdown of the key grounding and bonding aspects, referencing relevant NEC articles where applicable (remember, the specific edition of the NEC used in your area matters):1. Solar Panel Frames (Equipment Grounding)



Requirement

All metal parts of the solar panel frames
must be grounded. This is crucial for safety. You're creating a continuous, low-impedance path back to the grounding electrode system.

Method

Use equipment grounding conductors (EGCs) that are listed and identified for grounding purposes (typically green or bare copper wire). Many solar panels have pre-drilled grounding points with grounding lugs. Use these, ensuring proper contact. Bond each panel frame to the IntegraRack with approved grounding hardware. Bond the IntegraRack itself to the grounding electrode conductor (GEC), see section 4. Use star washers or other methods to ensure good metal-to-metal contact, especially in areas that might be subject to corrosion.

NEC Reference

NEC Article 690 (Solar Photovoltaic (PV) Systems), particularly sections related to equipment grounding. Also, NEC Article 250 (Grounding and Bonding).

Grounding Conductor Sizing

The size of the equipment grounding conductor depends on the overcurrent protection device (fuse or circuit breaker) protecting the circuit. Consult NEC Table 250.122 to determine the appropriate size. The wire you're using has to be rated for wet locations and sunlight resistance.
2.


IntegraRack Grounding



Requirement

The metal mounting structure (IntegraRack) must be grounded.

Method

Connect the IntegraRack to the main grounding electrode conductor (GEC) (described below) or a suitable grounding electrode. This ensures that the entire rack is at the same ground potential as the earth.


NEC Reference

NEC 690 and 250

Note

The rack itself is now a part of the grounding system.3.

Water Tote Tank Considerations



Requirement

Because you're using water tote tanks for ballast, the grounding system needs to be robust and reliable. There's a risk of isolation if the water dries out or if connections become corroded.

Best Practice

Consider adding supplementary grounding electrodes to the earth near the tote tanks. This creates a more reliable grounding path, even if the tanks' contact with the earth is compromised. Copper ground rods driven into the earth are a common solution.


Important

Bond the rack to these supplementary grounding electrodes.

NEC Reference

NEC Article 250.4.

Grounding Electrode Conductor (GEC)



Requirement

This is the main conductor that connects the equipment grounding system (solar panels, rack, disconnect) to the grounding electrode system (earth).

Method

The GEC connects to a grounding electrode system. This can be:


A Ground Rod

Typically, one or more copper or copper-clad steel ground rods, driven at least 8 feet into the ground. Two rods are often better than one, spaced at least 6 feet apart.

The Metal Water Pipe

If you have a metal water pipe entering your building that is in direct contact with the earth for at least 10 feet, it
can be used as a grounding electrode. However, it must be supplemented by another grounding electrode (e.g., a ground rod). You must bond to the water pipe within 5 feet of its entry point to the building.

A Concrete-Encased Electrode (Ufer Ground)

If available, this is often the best grounding electrode. It's a bare copper conductor encased in concrete near the foundation of the building.

GEC Sizing

The size of the GEC depends on the size of the service entrance conductors (the wires bringing power into your garage from the utility). Consult NEC Table 250.66 to determine the appropriate size.


Location

The GEC should connect to the grounding electrode system as close as possible to the service entrance (where power enters your garage).

NEC Reference

NEC Article 250, especially Sections 250.50 through 250.
70.5.


PV Disconnect



Requirement

The metal enclosure of the PV disconnect must be grounded.

Method

Connect an equipment grounding conductor from the disconnect enclosure to the grounding system (the GEC or a grounding electrode).


NEC Reference

NEC 690 and 250.6.

Underground Conduit



Requirement

The rigid metal conduit (RMC) you're using to run the PV wire underground
must be bonded to the grounding system at both ends.

Method

Use grounding bushings and bonding jumpers at each end of the conduit to connect it to the equipment grounding conductors in the disconnect box and the garage panel (or the grounding electrode conductor).

NEC Reference

NEC Article 250, particularly sections on metal raceways.7.

Garage Panel (Connection Point)



Requirement

The ground wire from the conduit must be connected to the ground busbar in your garage's electrical panel. The panel itself is already grounded through the service entrance grounding system.8.

Anker Solix F3800 Plus



Consult the Manufacturer

The most important step here is to
carefully read the Anker Solix F3800 Plus's manual. It should specify grounding requirements for PV input. Some units might require a specific grounding connection, while others might rely on the grounding provided by the system to which they're connected. Follow the manufacturer's instructions exactly.

Grounding Options (depending on the manual)



Grounding Electrode Connection

The manual might tell you to connect a grounding conductor directly from the unit to a grounding electrode (e.g., a ground rod).


Grounding Through the AC System

The manual might specify that grounding is achieved through the AC wiring when the unit is connected to the manual transfer switch and the garage's electrical panel. In this case, proper grounding of the panel is crucial.

Caution

Do
not assume that the unit is automatically grounded just because it's plugged into the wall. You must verify the grounding method with the manufacturer's documentation.9.

Manual Transfer Switch



Requirement

The manual transfer switch enclosure must be grounded.

Method

The transfer switch should be properly grounded through its connection to the garage's electrical panel. The panel's grounding system provides the grounding path.

Important Considerations



Local Codes

Always check with your local building department and electrical inspector for specific requirements in your area. Local codes can be more stringent than the NEC.

Licensed Electrician

It's highly recommended to have a licensed electrician review your plans and perform the final connections and inspections. This is especially important because of the underground wiring and the connection to your home's electrical system.


Ground Fault Protection

Consider using a ground fault circuit interrupter (GFCI) circuit breaker for the circuits powered by the Anker Solix F3800 Plus, especially if those circuits serve outdoor receptacles or locations where moisture is present.

Wire Types

Use conductors that are rated for outdoor, wet location, and sunlight resistance ("USE-2" or similar rating) for all wiring outside. THWN-2 is a common choice for wiring inside conduit.


Conduit Fill

Ensure that you don't exceed the conduit fill capacity. Consult the NEC for conduit fill tables.

Tight Connections

Ensure all connections are tight and properly torqued. Use anti-seize compound on aluminum connections to prevent corrosion.


Inspection

Have the entire system inspected by a qualified electrical inspector before putting it into operation.

Summary of Key Steps


Ground Panels

Ground each panel frame to the IntegraRack with appropriate grounding lugs and conductors.2.

Ground Rack

Ground the IntegraRack to a grounding electrode system (ground rod, water pipe, etc.). Consider supplementary ground rods near the tote tanks.3.

Ground Disconnect

Ground the PV disconnect enclosure to the grounding system.4.

Ground Conduit

Bond the metal conduit at both ends to the grounding system.5.

Connect to Garage Panel

Connect the underground conduit's grounding conductor to the ground busbar in your garage panel.6.

Anker Solix F3800 Plus

Follow the manufacturer's grounding instructions.7.

Ground Transfer Switch:
Ensure the transfer switch enclosure is grounded through the panel connection.By following these guidelines and consulting with qualified professionals, you can create a safe and code-compliant solar panel system for your backup power needs. Remember, safety is paramount! Flag for review

Previous Question Next Question