User: ChesterDawg, Location: CA
Asked on: Sunday, October 5, 2025 at 4:29 pm EDT
Answered on: Sunday, October 5, 2025 at 4:31 pm EDT
Question: Doing some apartments with a 120/208 3 phase service and 125 amp 120/208 single phase to each apartment.Having trouble finding any of the usual panel manufacturers with 2 pole GFCI breakers rated for 208v.What are you guys using for something like this?
You're right, finding 2-pole GFCI breakers specifically rated for 208V is tricky. Most common 2-pole GFCI breakers are designed and rated for 240V systems. However, there are solutions
1. Using a 240V Rated GFCI Breaker (Most Common & Recommended)
Theory and Code Compliance
While technically rated for 240V, many manufacturers will allow for the use of a 240v 2-pole GFCI breaker on a 208V system. The 240V rating is a maximum voltage rating. The breaker will still function properly at 208V. Check with the manufacturer, but generally this is acceptable.
Why it works
GFCI breakers detect current imbalance between the hot legs and the neutral. The voltage rating primarily dictates the insulation and dielectric strength of the breaker. A breaker rated for 240V can safely handle 208V. The GFCI tripping mechanism relies on current differential, not voltage.
Manufacturers
Siemens
Siemens breakers are often used in this application.
Eaton
Eaton breakers are another reliable option.
Square D
Square D (Schneider Electric) is a common brand, but confirm their stance on using 240V breakers on 208V.
IMPORTANT
Verify with the Manufacturer Before using a 240V rated breaker on a 208V system, contact the manufacturer directly to confirm their position and ensure it doesn't void any warranty or violate listing requirements. Keep a record of their confirmation (email or phone call log).2. Alternative GFCI Protection Methods (Less Common in Apartment Panels)
GFCI Receptacles
In some situations, you might be able to use GFCI receptacles at the point of use instead of a GFCI breaker. This is usually not desirable in the main panel.
GFCI Deadfronts These are essentially GFCI receptacles in a small box without any output terminals. Can be difficult to fit these and a 2-pole breaker in the same panel.
Panel Considerations
Panelboard Voltage Rating
Ensure the panelboard itself is rated for 120/208V 3-phase. This is usually standard, but always double-check.
Neutral Busbar
The neutral busbar must be adequately sized to handle the neutral current from each apartment.
Space
Make sure the panel has sufficient space to accommodate the required number of 2-pole breakers, including any spares.
Code Considerations (NEC)
NEC 210.8
This section outlines the requirements for GFCI protection in dwelling units (apartments). Specifically, pay attention to requirements for kitchens, bathrooms, laundry areas, and outdoor receptacles. The 2020 NEC now requires GFCI protection for all 120V through 250V receptacles supplied by single-phase branch circuits rated 150 volts or less to ground.
Local Amendments
Always check for any local amendments to the NEC that might have stricter GFCI requirements.
AHJ (Authority Having Jurisdiction)
Consult with your local electrical inspector (AHJ) to confirm their interpretation of the code and acceptable GFCI solutions for your specific project. Their approval is crucial.
Steps to Take
Identify GFCI Requirements
Determine exactly which circuits in each apartment require GFCI protection based on the NEC and local codes.2.
Contact Manufacturers
Reach out to Siemens, Eaton, and Square D (Schneider Electric) technical support to confirm their stance on using their 240V 2-pole GFCI breakers on a 120/208V system. Get this confirmation in writing if possible.3.
Panel Selection
Choose a panelboard that is properly rated, has adequate space, and is compatible with the chosen breakers.4.
Submit Plans
Submit your electrical plans to the local AHJ for approval. Clearly indicate the GFCI protection strategy you are using.5.
Installation
Install the panel and breakers according to the manufacturer's instructions and NEC requirements.6.
Inspection: Have the installation inspected by the AHJ to ensure compliance.By following these steps, you can ensure a safe and code-compliant electrical system for your apartment project. Don't take shortcuts, and always prioritize safety and code compliance. Flag for review