User: Jimmy7, Location: Boston, MA
Asked on: Monday, October 6, 2025 at 7:05 am EDT
Answered on: Monday, October 6, 2025 at 7:10 am EDT
Question: My apprentice was installing a fan and light combo in a bathroom. He tells me that he had trouble stripping the green ground wire of the fan and light combo after the fact. He stated that he kept losing strands of wire every time he tried to strip the wire. On his last attempt he stated that he got enough strands and connected it to the #14 bare ground. I took a look and the green wire is short, but looks to be connected properly. I don’t want to check it because I’m not sure I have enough wire to re-splice. To check it can’t I just do a continuity check between the exposed bare #14 and the housing?
Yes, your plan to perform a continuity check between the exposed #14 bare ground wire and the metal housing of the fan/light combo is a good and safe way to verify the integrity of the grounding connection without having to disturb the existing connection. Here's why it works and some additional things to consider
Why a Continuity Check Works:
Purpose of Grounding
The purpose of a grounding system is to provide a low-resistance path for fault current to return to the source. This allows a circuit breaker or fuse to trip quickly in the event of a short circuit, preventing electrical shock hazards.
Continuity = Connected
If there is good continuity (low resistance) between the ground wire and the metal housing, it means there is an unbroken path for current to flow. This verifies that the housing is properly grounded.
Testing the Path
By checking continuity between the bare ground wire and the housing, you are essentially testing the entire grounding path from the ground wire connection, through the green ground wire to the fan/light housing.
How to Perform the Continuity Check (Safely)
Turn OFF the Power
This is absolutely critical. Turn off the circuit breaker that supplies power to the fan/light combo before you do anything else. Double-check with a non-contact voltage tester to ensure the circuit is de-energized.2.
Set Your Multimeter
Set your multimeter to the continuity setting (often indicated by a diode symbol or an Ohm symbol).3.
Connect the Leads
Touch one multimeter lead to the exposed #14 bare ground wire. Make sure you are making good contact with the bare metal. Touch the other multimeter lead to an unpainted, clean, metal part of the fan/light combo housing.4.
Observe the Reading
Good Continuity
The multimeter should show a reading very close to zero ohms (or the meter will beep, depending on the type of multimeter). This indicates a good, low-resistance connection.
No Continuity
The multimeter will show an open circuit (OL or infinity symbol) or a very high resistance. This indicates a break in the grounding path, and the connection needs to be fixed.
Important Considerations
Low Resistance is Key
A slightly higher than expected resistance reading does not necessarily mean there is a problem. However, the resistance should be very low (typically less than 1 ohm) for a good ground connection.
Weak Connection
If the ground wire is only connected by a few strands, it could create a high-resistance connection that may not be reliable under fault conditions. Even if you see continuity, if the connection looks weak, it's best to redo it if at all possible.
Wire Length
If you are concerned about the green wire being too short, consider using a pigtail. Strip back a small amount of insulation from the green wire, if possible, and attach a short length of appropriately sized green insulated wire with a wire connector. Connect the other end of the pigtail to the #14 bare ground wire.
Future Proofing
Consider replacing the fan/light combo if the ground wire is chronically short or brittle, especially if you can get a slightly better unit or one with an easier to work with grounding system. It is better to have a fully functional ground.
If you find NO continuity
Inspect the Wire Connector
Make sure the #14 ground wire is securely connected to the green ground wire. It's possible the connection came loose.*
Check the Green Wire
If the connection looks good, visually inspect the entire length of the green wire for any breaks or damage.
In Summary:
Performing a continuity check is a safe and effective way to verify the grounding connection. If you get a good continuity reading, that's a good sign, but always keep an eye out for any visual indicators of a poor connection and redo the connection if necessary. If the connection is truly questionable or you have concerns, don't hesitate to replace the ground wire if at all possible to ensure a safe and reliable installation. Remember, safety first! Flag for review