User: G3PO, Location: NC
Asked on: Monday, October 6, 2025 at 11:02 am EDT
Answered on: Monday, October 6, 2025 at 11:19 am EDT
Question: I have a comms panel in 1 building being fed by a non UPS circuit from that building. Looking to add a 2nd UPS circuit from a second building to add redundency for this panel. Is this allowed As stated?
Connecting two different UPS systems, potentially from separate buildings and power sources, to the same comms panel can be problematic and potentially violate electrical codes. Here's a breakdown of why and what to consider
Potential Problems and Code Violations:
Backfeeding
Connecting two UPS systems in parallel without proper synchronization can lead to one UPS backfeeding power into the other. This can damage the UPS units, create an unsafe condition, and potentially violate electrical codes regarding parallel power sources. Backfeeding is a dangerous condition that can energize circuits unexpectedly and create a shock hazard.
Grounding Issues
Each building likely has its own grounding electrode system. Connecting circuits from two different buildings can introduce ground loops, which can cause noise in the comms system, potentially damage equipment, and also be a safety hazard. Ground loops can also cause equipment to fail sooner than expected.
Voltage and Frequency Synchronization
Even if the UPS units are from the same manufacturer and set to the same voltage, there can be slight differences in voltage and frequency. These differences, even small ones, can cause instability when the systems are connected together, leading to equipment damage or unexpected power outages.
Neutral-Ground Bonding
Each building's main service panel has a neutral-ground bond. If you're bringing power from a second building, it's crucial to ensure you're not creating a second neutral-ground bond. This can create parallel neutral paths, leading to circulating currents and potential safety hazards.
Fire Hazard
Improper wiring or backfeeding can cause overheating and potentially lead to a fire.
NEC (National Electrical Code) Compliance
The NEC has specific requirements for wiring methods, overcurrent protection, grounding, and separation of power sources. Connecting power from two different buildings will likely require strict adherence to these codes, and it may be difficult or impossible to do it safely and legally without significant modifications.
Manufacturer Warranty and UL Listing
Connecting equipment in a way that's not explicitly supported by the manufacturer can void warranties and potentially invalidate UL listings.
Permissible Ways to achieve redundancy
Automatic Transfer Switch (ATS)
This is the
recommended and safest solution. An ATS automatically switches the load (comms panel) between the two power sources (the main power and the UPS from the second building). The ATS ensures that only one power source is connected to the comms panel at any given time, preventing backfeeding and other issues. The ATS must be properly sized for the load and the available fault current from each source. The ATS must be installed by a qualified electrician and comply with all applicable codes. A properly installed ATS also handles the neutral and ground connections correctly. ATS units usually have a break-before-make design, so there will be a millisecond blip during transfer to the alternate circuit, but that shouldn't affect a UPS.2. Parallel UPS System (Specialized UPS)
Some UPS manufacturers offer systems specifically designed for parallel operation. These systems have built-in synchronization and control circuitry to ensure safe and reliable operation. These are usually much more expensive than standard UPS units and need to be set up correctly.3.
Double Conversion UPS
Also referred to as an online UPS, this type will convert from AC to DC, and then to AC again. This creates a very clean output and isolation between the two sources.
Important Considerations
Consult a Qualified Electrician
Before attempting any wiring changes, consult with a licensed and experienced electrician. They can assess your specific situation, determine the best solution, and ensure that all work complies with local and national electrical codes.
Permitting and Inspections
In many jurisdictions, any electrical work requires a permit and inspection by the local authority. Make sure to obtain the necessary permits before starting work.
Documentation
Keep detailed documentation of all wiring changes, including wiring diagrams and equipment specifications.
Grounding Electrode System
Ensure that the grounding electrode system in each building is properly installed and maintained.
Overcurrent Protection
Each circuit must be properly protected with appropriately sized circuit breakers or fuses.
In summary, directly connecting two separate UPS systems from different buildings to the same comms panel is generally not allowed and can be dangerous. Using an Automatic Transfer Switch (ATS) is the safest and most reliable method for achieving redundancy in this situation. Always consult a qualified electrician to ensure that all work is done safely and in compliance with applicable codes. Flag for review