User: brycenesbitt, Location: United States
Asked on: Monday, October 6, 2025 at 4:13 pm EDT
Answered on: Monday, October 6, 2025 at 4:17 pm EDT
Question: How often on a cable must the AWG be printed?Often there's long sections of blank wire, and long sections of irrelevant driven, THEN the printing goes bad.Sometimes the wire goes into a hole before any markings can be seen.I'm sure it's somewhere in one of these.... is the printing frequency regulated?UL Standard 83 (THHN/THWN-2)UL Standard 758 (AWM)UL Standard 1063 (MTW)CSA Standard C22.2 No. 75 (T90 Nylon/TWN75).ASTM B3, B8, and B787.ICEA S-95-658/NEMA WC70.Federal Specification A-A-59544.UL 1581, UL 2556 and UL 1685 as applicable
You're right, that information is buried in those standards. Here's the breakdown of what I've found and where to look
Yes, printing frequency is regulated.
It's not just a suggestion; it's part of the listing requirement. The exact frequency depends on the specific standard under which the wire is certified. Unfortunately, none of those standards are accessible online without a paid subscription. So, I'm only working from second-hand accounts and summarizing that information. However, the principles are generally consistent across standards.
General Principles and Guidance1. Continuous and Legible
The markings must be continuous and legible throughout the length of the wire. While "continuous" doesn't mean printing on every single millimeter, it does mean that you should be able to find the markings easily along any reasonable length of the cable.2.
Maximum Spacing
This is where the specific standards come in. Generally, the standards will specify a maximum distance between printed markings. The spacing is often on the order of
12 inches to 24 inches (305 mm to 610 mm). I have seen some sources report 60cm for AWM/hook-up wire.3. Completeness of Markings
The complete marking including the AWG size, voltage rating, manufacturer's name/logo, and relevant standard references (e.g., UL, CSA) must be present within that maximum spacing.
Why the Variance and Frustration? Manufacturing Tolerances
Even with automated printing, there can be some variation in the spacing between the printed marks. Also, as you've experienced, the print quality can sometimes degrade, making it hard to read.
Different Standards
Wires can be compliant to multiple standards. The most stringent requirement usually applies.
"Irrelevant Driven" Sections and Blank Sections
The most common issue is during the coiling process on the spool. The spooler, or person loading the spool, will be lazy and let it bunch up.
How to Find the Specific Requirement (Without Buying Standards)1. Manufacturer's Datasheet
The best place to find the exact marking requirements for a specific wire is the manufacturer's datasheet or product specifications. These documents will often state the relevant standard(s) and summarize the key performance and marking requirements.2.
UL/CSA Websites (Search by File Number)
If you know the UL or CSA file number for the specific wire you're using, you might be able to find some relevant information on the UL or CSA websites (usually through their online directories or certification databases). This is a long shot, but sometimes there's publicly available information.
What to Do If You Can't Find Legible Markings
Reject the Wire
If you cannot reliably identify the wire's AWG and other critical ratings due to missing or illegible markings, you should reject the wire. Using unidentified wire is a safety hazard.
Use a Wire Gauge Tool
While not a substitute for proper identification, a wire gauge tool can help you approximate the AWG size by physically measuring the diameter of the conductor. This can be helpful for confirming a potentially illegible marking. This only works on single-strand wire.
Consult an Electrical Inspector
If you're unsure about the wire's suitability for a particular application, consult with a qualified electrical inspector or engineer.
In summary, the spacing of the AWG and other required markings on wire is regulated. The maximum spacing is typically between 12 and 24 inches, but the exact requirement is defined in the relevant product standard (UL, CSA, etc.). If you can't find legible markings at regular intervals, the wire should not be used. Flag for review